Jump to content
SAU Community

Na Power Results - All N/a Engines


Recommended Posts

Just for a laugh.

1985 honda civic

890kg

1.6l DOHC ZC (not vtech yo) jap spec engine implant. 130HP at the crank from factory.

Mods: Extractors

rev cut 7500

15.5 down at WSID

100HP atw (75kw) lol at R31 club dyno day

Don't have it anymore.

Link to comment
Share on other sites

My friends setup

R33 GTS

Rb25DE

-6-3-1 Custom Extractors > 2.5" Exhaust > Oval Muffler at rear

-Pod Filter in fibreglass box with a S/S intake pipe with factory AFM

-Apexi PowerFC

-GTR Injectors ( i think he said , not sure about that one)

-111.5rwkw / 149.41rwhp

VL Calais

RB30E

-6-3-1 Extractors > 2.5" Exhaust > single Oval Muffler dumped at Differential

-High Flow panel filter into custom Twin Throttlebody setup

-Tuned and Chipped factory ECU

-93rwkw

Link to comment
Share on other sites

  • 1 month later...
  • 3 months later...
  • 1 month later...
ok, well i will list my 2 natro cars that i have had on the dyno (neither skylines though). will scan dyno sheets when i find them.

2000 n15 SSS pulsar

genie extractors

2" press bend system (which i want to get redone because it is just one we bodged up 1 arvo) with 12" centre resonator and lukey muffler (not a cannon)

k&n panel filter

fuel - dunno. probably 91 octane. can't remember

112hp atw (approx 84kw)

2000 mitsubishi magna (3.5L manual)

first run: 100% stock, rear muffler was a cannon, but rest of the piping was stock

159hp atw (approx 118kw)

second run: pacemaker extractors, 2.5" redback centre system (cat to rear axle), 2.5' lukey rear system k&n panel filter

170hp atw (approx 127kw)

1999 magna (same as previous one, manual 3.5L)

never dyno'd, but felt more powerful as the previous one had been thrashed a fair bit.

redback 2.5" exhaust

14.8 at willowbank with 2.18 60ft time

just found all my dyno sheets, etc

pulsar

pulsardyno.jpg

first magna (and people say that you can't get a smooth dyno graph from a stock ecu, LOL)

magnadyno.jpg

second magna drag slip

dragyu8.jpg

Link to comment
Share on other sites

  • 2 weeks later...

honda integra type r i no wrong site waiting till my 32 gtr arrives lol

b18cr new injectors arc pod filter 5zigen 3 inch exhaust vafcII 175hp fw

Link to comment
Share on other sites

Once I get my extractors I hope to get them installed and tuned and get some power figures up

The setup will be as follows

1992 E-HR32 GTS

RB20DE (Automatic)

COBY 6 -2-1 (2.5 outlet) to standard cat then 2.5" exhaust back to a canon muffler (loud)

Large K&N pod filter on stock intake piping (will modify later)

R33 series 2 - 4SPD Auto box (re4r01a) Which has a Stage 2 modified valve body

R33 series 2 torque converter

Advanced timing

Always have run on 98 octane premium Shell or caltex fuel

Suspension and braking below:-

Complete nolathane bush kit

Japanese Aluminium adjustable front Strut brace

Pedders Larger rear sway bar

Pedders sportsrider lowered suspention all round

R33 N/A Complete rear brake setup (4 stud)

R33 GTS-T slotted Front Rotors (re drilled to 4x114.3 pattern)

R33 GTS-T - 4 piston Front calipers (gold painted)

17" SSA wheels with 215/45R17 rubber

Looking at between the 100-120 Rwkw mark hopefully

Link to comment
Share on other sites

Internally stock RB20de

some random muffler otherwise stock exhaust

K and N pod filter (needs cleaning)

everything else is stock

86.7KW on a 30 degree day ill search for the dyno sheet it was done in TAFE just for laughs

Link to comment
Share on other sites

  • 2 weeks later...

2005 VZ SS ute

5.7l GenIII

4spd auto

cold air intake

Pacemaker extractors

HSV hiflow cats

2 1/2 inch stainless twin system with rwc muffler

LS1 Edit

239.9rwkw at aussie mufflers dyno

its running rich in the top end for towing duties, If i where to lean it out and get a retune, it would make about 260kw.

Link to comment
Share on other sites

  • 1 month later...
  • 1 month later...
Just an update, had new exhaust put on the car, went from 137rwkw to 152rwkw, so i'm finally making 200hp at the treads.

Went back for a Retune with the new exhaust, I am now making 154.6rwkw (207Hp) as far as I know it's the 2nd most powerful N/a RB in Australia.

Link to comment
Share on other sites

nice!! goes to show that if you invest $$ into an N/A RB you can still make some good N/A power! Do you have a dyno graph? I'm interested to see visually what the power delivery is like. What's the torque like down low being that it's an RB30/26, I'd expect it to have some nice bottom end.

Link to comment
Share on other sites

nice!! goes to show that if you invest $ into an N/A RB you can still make some good N/A power! Do you have a dyno graph? I'm interested to see visually what the power delivery is like. What's the torque like down low being that it's an RB30/26, I'd expect it to have some nice bottom end.

IMG_0991.jpg

This one doesn't have the torque curve on it but it sits almost flat from 2000 to about 6000rpm at around 350Nm.

Link to comment
Share on other sites

  • 4 weeks later...
Went back for a Retune with the new exhaust, I am now making 154.6rwkw (207Hp) as far as I know it's the 2nd most powerful N/a RB in Australia.

Not for long :down:

Nice graph though, would be really nice to drive, mines the same but a bit of a gap down low and it keeps climbing up top (more duration cams).

If you gave it some mild cams i reckon you could easy net another 15-20kW from it (but atm it looks like it would have beautiful drivability)

Link to comment
Share on other sites

  • 3 weeks later...
  • 3 weeks later...

It's not mine, but my cousins manual MR30 with RB30/25DE made 144.6rwkw with a Haltech, injectors, 6-3-1 extractors, 2.5" exhaust and a K&N pod

Never owned a Skyline, the only car I ever put on the dyno was my Scorpion with extractors, a Weber, 2.25" exhaust and 5 speed, it made 67rwkw :huh:

Edited by jwebb2876
Link to comment
Share on other sites

Rb 25 NA standard internals; nvct; 256 -degree Tommie cams; custom plennum with Falcon T/B; custom 6 into 3 into 1 extractors(no cat); Autronic set at 22 degrees-164 rwlklwts at 7600 rpm on Jakes Dyno( ACT ) in clubman sportscar road registered and 720 kgms

Link to comment
Share on other sites

Engine:VQ35DE

Car: V35 Skyline Coupe

Mods: Z-tube and pop charger, Plenum spacer.

Power: 177rwkw.

Putting the Exhaust Headers on monday and a grounding kit. Will do a new Dyno run sometime next week. :bunny: Hopping for 185rwkw

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




×
×
  • Create New...