Jump to content
SAU Community

Gear Box Breather


PIOTREK
 Share

Recommended Posts

about 3000km ago i recently changed the gearbox oil to redline lightweight shock proof (smurfs blood) in my r33 turbz. i started to get a bit of fluid coming out of the breather valve, i'm pretty sure. so i ran a rubber hose to the top of the engine bay. its been a while and i'm still getting a little bit of fluid coming out of the hose and onto the engine bay.

the bolt on the side of the gear box has been taken off, and got the correct amount of oil in it. and nothing extra came out of the breather valve.

approx close to the full bottle of fluid went in, about 3.5L i think and was poured in through the shifter inlet, inside the car.

Now anyone got a simular problem? any advice.

i want to place the rubber hose somewhere else as i'm stick of taking the oil off the engine :P

however i'm trying to work out if everything is normal.

Link to comment
Share on other sites

Hmm, when I did a fluid swap with the lightweight-shockproof I had no leakages that I knew off. Maybe you over filled it? Though I recall using a full us gallon plus a touch extra to get mine to the filler hole (I filled through this with a pump bottle). I did let mine drain overnight though.

It should only leak if it's got too much I'd of thought but I'm not an expert. We're talking a 5-spd manual right?

Link to comment
Share on other sites

Hmm, when I did a fluid swap with the lightweight-shockproof I had no leakages that I knew off. Maybe you over filled it? Though I recall using a full us gallon plus a touch extra to get mine to the filler hole (I filled through this with a pump bottle). I did let mine drain overnight though.

It should only leak if it's got too much I'd of thought but I'm not an expert. We're talking a 5-spd manual right?

yer its the 5 speed turbo, NOT A GTR or auto

is it ok to fill it via the shifter? because i was reading that gtr can't because of the transfercase, is that right?

Link to comment
Share on other sites

open up the filler plug and see if anything comes out. if oil comes out, you over filled it. from time to time they will throw out oil during hard driving, usually only happens on the track though. you can lengthen the breather, or other solution i've seen on track cars is to make a little expansion tank at the end of the breather. so the breather feeds into a vented tank which then allows the oil to drain back down into the box. but on a road car you shouldn't be having the problem. the other less happy answer is that something is wrong with the box, but it's more commonly just too much oil.

yes GTR cannot be filled via the shifter hole as the GTRs shifter goes into the transfer case, not into the gearbox. GTS4 is the same. GTST is fine to fill through the shifter hole, but personally i find it easier and less chance of overfilling and less chance of mess to just fill it through the filler plug as it's meant to be. :domokun:

Link to comment
Share on other sites

K thanks, however has anyone had a similar problem? Cause I'm considering putting in another type of fluid but the box itself feels really good using the light weight shockproof RedLine stuff. Not sure but is there an simple explanation? Some tell me to only pour 3L in! Anyone no wat Nissan reccomend?

Link to comment
Share on other sites

Mine took a whole gallon bottle and then a bit more using a pump bottle and the filler hole.

I let mine drain overnight.

Boys i gotta say a simple question like how much oil in your 5speed and only 1 response (2 in thread)

Thanks action dan :blush:

Link to comment
Share on other sites

  • 2 weeks later...

your only spose to fill it up to the filler hole on the side of the gear box, if you must fill it throught the shifter then have the filler hole open and when it starts comming out of that hole then it full,

if i was at home id look up the specs in a workshop manual for you but im not home for a few weeks

Edited by s13_Skyline_inside
Link to comment
Share on other sites

  • 5 years later...

I'm having the same problem.

I had a look under the car after a long country drive to find a fair bit of blue gearbox oil at the rear of the gearbox and on the crossmember:

14745387030_60ffa9ae6f.jpg

The car's also recently been on the dyno so it may be from that too. It's an R34 GTT with R34 RB25DET gearbox and Redline Lightweight Shockproof.

I had a better look today and it's definitely coming from the breather:

14745485537_9e1f49151e.jpg

Is there meant to be a hose connected to the breather? If so, where does it connect to? This is a recent conversion so maybe this is something that's been missed in the install...

I was just trying undo the driver side 1/2" plug (refer right arrow below) on a level surface to check the oil level, can't get enough leverage, is there a good trick to this?

14909055526_86d17e1463.jpg

Thanks!!

Link to comment
Share on other sites

Got the filler plug open yay. There's still oil in there but I'd estimate the level to be 2-3 mm down from the edge of the filler hole. Photo below though it's a bit hard to see.

How much oil do you reckon I need to fill it up to full? And how do I fix the breather hose so this doesn't happen again??

Cheers

14931828682_64163a0a69.jpg

Link to comment
Share on other sites

Yes, breather runs up to there. Someone with small hands might be able to fit it up as per original, but it doesn't have to go there. Just get a long bit of hose and run it up behind the engine and fasten it to some convenient point.

FWIW, my breather hose runs up to the normal spot and I still get the shockproof foaming up and bleeding out of it. It does it when the car gets a flogging. So I am going to (one of these days) extend my breather hose up higher anyway.

Edited by GTSBoy
Link to comment
Share on other sites

I had the same issue, i put a common clear plastic fuel filter ( for a carby engine) in the middle of the breather hose and ran the end to up behind the head (as per factory). This fixed the problem, the fuel filter acts as a oil/ air separator, and only cost a few $.

Link to comment
Share on other sites

Yes, breather runs up to there. Someone with small hands might be able to fit it up as per original, but it doesn't have to go there. Just get a long bit of hose and run it up behind the engine and fasten it to some convenient point.

Cool I'll do that. I assume I can use any old auto hose for this?

I had the same issue, i put a common clear plastic fuel filter ( for a carby engine) in the middle of the breather hose and ran the end to up behind the head (as per factory). This fixed the problem, the fuel filter acts as a oil/ air separator, and only cost a few $.

Great idea! Do you mean one of these:

EMPI-VWFuelFilter.jpg

Silly question, which way around should this go?

...

Also another thing, it looks like my breather connector is bent, it's pointing down not forward (see photo of gearbox above). I'm not too keen to trying to bend it back as it might crack. What this means though is that there will be a bend in the hose and some oil may sit there, will this be a problem?

Link to comment
Share on other sites

That filter is a little motorbikey one. It'll probably work, but the cheap $2 ones (that look like the original Ryco ones, about 65mm long, maybe 50mm diameter) are probably better. They have more volume inside.

Fit it so that the outside is connected down to the gearbox. The inside of the filter element should face atmosphere.

Use low pressure fuel hose for best resistance to oils.

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




×
×
  • Create New...