Jump to content
SAU Community

S14 With Neo Rb25 Drift Car.


Recommended Posts

  • 3 weeks later...

so yesterday i got stuck into doing injectors... had to modify the fuel rail to suit the new Deka 620cc injectors as they are 12mm taller overall. this raises the rail up and nearly fouls the bottom of the top part of the intake manifold.

also some pics of Andrew half way thro the manifold.

image0641.jpg

image0642.jpg

image0651.jpg

image0647.jpg

image0649.jpg

Link to comment
Share on other sites

some more minor stuff happening.

Cheers to Cazman for getting the wheel for me. pretty sweet and perfect for the price.

image0662.jpg

another bay shot. i have now modded the rad some more for extra clearance between the fan and the rad.

image0663.jpg

Throttle cable is a S14 sr one and almost fits the neo. just needed to move the mount 40mm further forward and it fits. Made custom mount using 3mm stainless and water jet cutter.

image0664.jpg

image0671.jpg

Link to comment
Share on other sites

got my front wheels on, wound in some low on the coilovers and they sit ok for now... i'll see how it drives first and then i might lower it some more yet,

andrew got to work doing the exhaust... got the mufflers done today and had a set back involving the air compressor catching on fire lol.

image0682.jpg

image0688.jpg

image0687.jpg

image0691.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • And I hope the relay receives the trigger signal from the ECU and not the ignition power. It should prime and stop if the motor isn't running.
    • I disconnected before the fuel pump and restriction still there. Disconnected at turbosmart fpr and also after ethanol sensor and pressure dropped. No kinks in line but I found one spot above diff that I can hear the fuel flowing while running so I'm wondering if there is built up corrosion  from 10 years of sitting.  I had injectors cleaned and tested and one was dead but rest were fine. Was never an issue when I owned the car previously but I'll talk to jez about his thoughts on if they should be changed to newer tech. Thx guys at least I know the setup should work again. Pump is wired directly to relay and not using factory plug any  more 
    • Nice work on the shroud/ducting.  
    • Hi and best of luck with your car. Its a bit hard to tell how low the car is all round from that pic or if its been lowered or not. 90mm is a bit low on the front apron but it depends on the shocks & springs condition & whether or not its been lowered. Going to 19” wheels will give you 15-20mm depending on rubber but you might need new shocks. Mine -2005 are weeping fluid slightly but have lasted 19years!!. So if yours are original they need replacing anyway if they havent been touched before.
    • Hi everyone, Recently got handed down a 2004 Skyline 350GT Coupe. I would like to change the wheels as the previous owner installed some weird ones. The current ones are 215/45ZR18, unsure of the offset, and sit pretty deep in. Would like to increase the ground clearance slightly as well as I need to get it roadworthy standard, currently sitting at 90mm. Was thinking that maybe I could kill 2 birds with 1 stone by getting new wheels.  Pictures of current wheels: https://imgur.com/bg1QMIu Any recommendations for the types of wheels I should be on the lookout for? Like the maximum and minimum offset, sidewall height, width, etc.  Sorry in advance if I'm noob, I do not know much about cars other than how to change the oil, a blown tyre and brakepads....
×
×
  • Create New...