Jump to content
SAU Community

The Fuel Pump Thread


Recommended Posts

Hey everyone

I've noticed there isn't much into on fuel pumps etc when searching the forum so I thought I would add some of my own stuff.

So here is a bit of info that I can give. I am also after a few other opinions.

I'm a Nismo man, I have never had any issues with the Nismo 275lph pump that they make a drop in for most Skylines. Problem is, these don't have official E85 support.

I've been looking at these pumps:

1. Walbro 400lph E85 Pump (Apparently some issues with priming?)

2. Deatschworks 320LPH Version 2 E85 Pump

3. Bosch 044

4. Nismo 275lph Straight drop in

Okay... so there are other catches... like factory wiring. Does anyone have an idea on what sort of amperage the factory wiring can handle? I've been looking at flow charts and comparing amp draw with PSI etc.

Here are some flow charts.

Walbro 400lph

Walbro-400-Fuel-Pump-Flow-Charts.jpg

Deatschworks 320LPH Version 2

DW301MarketingTechData2.jpg

Random Pumps

FuelPumpflowchart1.jpg

Deatschworks 320LPH Version 2 again

DeatschworksDW300Flow.jpg

The FLow charts are definitely interesting.

My intentions are:

Replace the factory fuel pump in my BNR34 with a decent pump that will do 400awkw, and from there, when its time to go for more power, I will add an aftermarket industries surge tank, and use the twin Holley Dominator 1400 pumps to feed my injectors. (ID 1300cc Stainless)

Currently installing 2 x HKS 2530s and supporting mods.

Your input would be appreciated.

The Mafia

Link to comment
Share on other sites

I run twin Walbro 255's, less current draw than the e85 pump and more flow. Still I had to upgrade the tank lid for the extra current draw and flow requirements. I ran twin feed lines, one to each rail on the VQ.

For 400+kw intank, single pump, the e85 Walbro is probably your best option, but you may have to re-pin the plug at a minimum. I have had issues with the DW pumps on ethanol, and will never use one again.

Link to comment
Share on other sites

I run twin Walbro 255's, less current draw than the e85 pump and more flow. Still I had to upgrade the tank lid for the extra current draw and flow requirements. I ran twin feed lines, one to each rail on the VQ.

For 400+kw intank, single pump, the e85 Walbro is probably your best option, but you may have to re-pin the plug at a minimum. I have had issues with the DW pumps on ethanol, and will never use one again.

Hey mate

Can you go into more detail about the issues you had with the DW pumps? Was it an isolated issue or common?

Link to comment
Share on other sites

I had a couple fail on e85 builds, and the warranty process is farked. Now I just stick to e85 Walbro's as they are cheap ($185) and they work flawlessly. (Unless you try and run water through them :P)

The e85 Walbro uses turbine tech, not gear pump. They are silent.

Link to comment
Share on other sites

The early E85 walbros had an issues if not submerged fully, the later not so much, I have the newer E85 walbro in my 34 as a lift pump and have run it way down past the pump hieght with no issues :)

What sort of issues do they have? I've got one mounted in the standard position in tank (r34 gtr). Should I be trying to mount it further down the mount like in a 34 gtt?

Link to comment
Share on other sites

What sort of issues do they have? I've got one mounted in the standard position in tank (r34 gtr). Should I be trying to mount it further down the mount like in a 34 gtt?

Do you have problems with fuel surge under 1/4 tank ?

If not you must have a " newer " one, if so you will need to lower it or swap it out

Link to comment
Share on other sites

Personally, I wouldn't waste my time with a walbro externally. There are better options.

Aftermarket industries makes beautiful surge tanks, and they also sell the Holley Dominator 1400 and 1800 external billet pumps.

Worth every cent.

http://www.aftermarketindustries.com.au/fuel-pumps--accessories-c3/holley-dominator-1400-p180/

http://www.aftermarketindustries.com.au/fuel-pumps--accessories-c3/holley-dominator-1800-p92/

Link to comment
Share on other sites

Okay, assuming I don't want to make 1000hp and have a mild setup and already have a surge tank and am just looking for an external pump. What else is out there besides Bosch (have had great experiences with Walbro so would like to stick with them of possible)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



×
×
  • Create New...