Jump to content
SAU Community

New Owner 1993 R32 Gtr Vspec.


glaze
 Share

Recommended Posts

Tint and plates done. Not that you can see tint here. Next, looking to get both front & rear bars resprayed and put some nice 18" Black Enkei RPF1 or something similar on:)

C5XYMJ.jpg

Tip for your very bent front license plate : try getting some washers or similar to use as spacers. That way your plate won't look like they were put on by the work experience kid at a car dealer :)
  • Like 1
Link to comment
Share on other sites

If you can find some plastic rod (nylon, HDPE whatever, doesn't really matter) of about 20mm or a little less diameter and however long (say 15mm) you can drill them and then space out the number plate to clear your bumper. Will bend back a little by itself but doesn't look minger spec.

Also nice car. Not sure about the Enkeis. The RPF01's look a bit feeble on gtr's. Would go LMGT-4's if you have the coin.

Edited by djr81
Link to comment
Share on other sites

Yeh tough to get a solution for the plates! Im looking at putting on some nice 18's with a little dish, Im after a nice aggressive look.

Not sure of other wheel options as yet, but I have these Advans to get rid of to help free up funds for some new wheels:)

Link to comment
Share on other sites

Yeh tough to get a solution for the plates! Im looking at putting on some nice 18's with a little dish, Im after a nice aggressive look.

Not sure of other wheel options as yet, but I have these Advans to get rid of to help free up funds for some new wheels:)

It really isn't. Spacers or wheels. Its all a straight forward choice.

post-5134-0-87288500-1421713622_thumb.jpg

post-5134-0-57080800-1421713636_thumb.jpg

post-5134-0-32474700-1421713667_thumb.jpg

  • Like 3
Link to comment
Share on other sites

  • 4 weeks later...

Birds, Yeh I believe so. Couldn't be happier with the Impul rims Vs the Advan's. Never been much of a gold wheel person, but the aggressive fitment & black Impul's are very much to my liking ;)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • So latest update. I replaced the ignitor with a jspec unit from enjuku. It felt a lot better at first although it is a little bit cooler of a day than it has been. Warming up didn't have as much misfire sputtering as before. Went on a 10m test drive. Felt good, a lot stronger though I was taking it easy on the boost. On the return trip started getting the cutting out at higher rpm again and was getting worse the longer I was driving. Took it easy the rest of the way home. Before turning the car off was getting the normal idle sputtering I was getting before.  So where I'm at now, entire ignition system has been replaced with upgraded components. Plugs still gapped at .8mm. Removed the fuel cap in case it was building too much reverse pressure I'm the tank, didn't help at all. Now I'm still on the same tank of gas the fuel treatment was in, I'm thinking if I can run that out and then refill with fresh 93 maybe  the treatment is too concentrated in some areas but doesn't explain that it only does it once the car is warm. I'm leaning towards fuel pump or injectors but if the injector was clogging I don't think it would make it shut off like it has but then fire right back up like nothing happened. So my current guess would be the pump. Without a fuel pressure guage no way to test or check it while it's running.  So that's kind of where I'm at. Need to start testing fuel components and ecu/wiring but I'm at a loss of what's the next logical step and procedure for testing it. 
    • @niZmO_Man thanks for that info, lucky I bought the gktech ones 🤙.
    • Never cheap out on brakes, tyres, suspension. I learnt the hard way at Oran Park lol
    • You got your answer when everything was OK after disconnecting your return line from the FPR. Why in the world are you running a 460, 2200CC injectors, etc. on stock 8mm lines?  Keep the pump, ditch the lines. I used both 8mm lines as my feed and one of my Hicas 10mm lines as return. 
×
×
  • Create New...