Jump to content
SAU Community

Happy Laps - Queensland Raceway 12-04-15


Cadmoon
 Share

Recommended Posts

Event:
Happy Laps - Queensland Raceway
Description:
A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Also if you have not done QR before this is your ticket in to Lakeside.
Location:
Queensland Raceway
Date:
Sunday the 12th of April.
Time:
7:00 AM Arrival
Cost:
Slight change in the payment form these happy laps onwards:
$35 for members and guests of members who pre pay by direct deposit
$40 for members who pay on the day
$50 for non members
Please note that this is a per person cost, any passengers etc are required to pay as well.
Requirements:
1. QR have a minimum age of 12 for passengers.
2. No overtaking in the first 2 laps.
3. The overtaking car is responsible for completing the overtaking move safely.
4. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.
5. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.
6. Cars should not be more than 2 abreast at any point on the track.
7. Be aware of cars around you, in front and behind (and beside when being overtaken).
8. Do not assume that the car in front of you knows you are there.
QR RULES

10. There is to be no racing

11. The straights are speed limited to 120km/h

12. Any car that goes off the track will be pulled off

13. There is not to be more than 1 sec of tyre smoke.

14. There are to be no helmets

15. Vehicles must have current registration and number plates are not to be obscured in anyway

Payment Details:

Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012

PAYMENT REFERENCE: Username&HappyLaps

Attendees:
  1. Cadmoon +1
Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

great morning and good to see a good turn out,thanks for the 86 club members for showing up and everyone else as well,some of the racing afterwards was good too.

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
    • Nah, im after the more newer looking, one with the OLED display
    • We revised the neutral wire instructions. The old way was wrong.  R34 gearbox change.pdf
×
×
  • Create New...