Jump to content
SAU Community

M35 Seating Options


Philr32
 Share

Recommended Posts

What's everyone do with seats in their M35? The standard ones look quite flat and not very supportive in corners. Anyone can confirm? So what would alternative options be? I take it theirs aftermarket rails so you could bolt in bride, recaro, sparco etc easily? Anyone know if V35, 350Z or any other performance Nissan seats would bolt in easily, whether using the stagea rail or the rail from the V35, 350 etc?

Link to comment
Share on other sites

Ah yea pretty sure there's another guy with R35 seats Beregron or something like that I think. 350Z seats would be good if they weren't a huge headache. If they're a head then the gains aren't really worth it, probably better to go aftermarket

Link to comment
Share on other sites

350z & V35 seats are the same design, you can get them in a bunch of different trims, material, leather, half n half and they are pretty much straight bolt in.

Biggest issue with my V35 seats was getting the wiring to work because the seats weren't electric beforehand but even that was a 15 minute job.

post-116816-0-68912300-1448508141_thumb.jpg

post-116816-0-93134800-1448508173_thumb.jpeg

Link to comment
Share on other sites

I'm also looking at an M35 and wanted to look at options as I think the standard seats are probably fine and comfortable for the most part but I have a recaro in my current car and love how it hugs and holds me in. One look at M35 seats and you can see they aren't going to be amazing at holding you firm where you want to be.

Link to comment
Share on other sites

Get it on the track or up in the mountains and you will be using your knees to hold your arse steady. You sit on the stock seats, not in them, and they are high enough that you stare at the rear vision mirror instead of the road. My seats dropped my arse at least 3 or 4 inches at a guess. I suppose it depends how fast you want to go around corners at the end of the day, and how tall you are.

Link to comment
Share on other sites

Awesome, so all the bolt holes lined up?

Yep, lined up perfectly! No issues.

So why do people change there m35 seats? Are they just average or are you used to a different seat? Looking at purchasing a m35 I'm 6ft and 100kg. Is this a urgent change needed?

I'm 6'1 and not a light guy by any means, the stock seats although ok comfort wise are too high (head touches the roof) and have no side support, if you event half heartedly take a corner you'd slide everywhere. V35 seats are about 50mm lower and a hell of a lot more supportive.
Link to comment
Share on other sites

Get it on the track or up in the mountains and you will be using your knees to hold your arse steady. You sit on the stock seats, not in them, and they are high enough that you stare at the rear vision mirror instead of the road. My seats dropped my arse at least 3 or 4 inches at a guess. I suppose it depends how fast you want to go around corners at the end of the day, and how tall you are.

For me its just below knees on outside resting against that pocket to hold myself gets annoying and sore after a while

Link to comment
Share on other sites

Interesting you guys have trouble with height. I'm 5ft 10in and 92kg but I'm very short in the legs so have an upper body the length of someone about 6ft 2in, and I can get the seat low enough to have a decent amount of head room. My wife, who's only a fraction shorter than me (but in proportion so shorter in the body), jacks the seat up high and that starts to get tight but otherwise I've had no trouble with clearance. It took a while to get used to the base height after my Commodore but otherwise it's fine.

Maybe they changed for the facelift models?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • I mean technically you don't. And you don't need a wideband if your tune is good. But this is what I was getting at. It's really hard to tune something to that degree. Narrowbands are used to take a 'somewhat accurate map' into stoich, like a boost controller, and you're really just tuning how much 'work' it needs to do, with the aim of 'Better tune, Narrowband/Wideband has to compensate less' But anyone who has ever done something like tuned one day, then DARED to drive on a day where it's 5 degrees colder/warmer, or in a slightly hillier region, or slightly higher altitude will look at their tune and "If only there was some kind of device that could compensate on the fly and hit a target to account for...." And now you know why Narrowbands, Widebands, and things like MAF's exist.
    • Maybe go log your voltage vs. RPM as you doodling around town. The issue could be your alternator is cactus which has been supplying fluctuating voltage to the rest of your car thus killing your pump early.
    • Yeah, but maybe not. Maybe yeah. Maybe not. You know how it is. I mean, if the volts are low and the pump has reduced capacity, then it will maybe not be able to supply enough fuel to keep up with your peak demand, but it really shouldn't make it go lean as you're ramping up, then catch up again. The pump dynamics are (should be) a pretty instant trade off between flow rate and pressure, and even that shouldn't matter because it is actually the job of the fuel pressure regulator to take care of that dynamic, leaving the pump to see pretty much the same pressure and flow conditions any time the engine is running.
    • One thing I do like about innovate is their ability to simulate a narrowband O2 output, great for deleting the OEM O2 and feeding that 0-1V simulated voltage back to the stock ECU. Great for PowerFC users, Nistune users that do not have the luxury of ingesting wideband 02 data. And before anyone says "yOu doN't nEEd O2 fEEdbACk iF yOUR tUNe is goOd" can GTFO.
    • The R32 ECU won't know why it is misfiring. This is likely to be a problem with the speedo drive cable. it could be broken and still driving, but lets go from time to time (which is unlikely, but possible). You could have damage at the plastic connector between it and the input to the speedo head. That's where mine broke. You could have gearbox oil creeping up the drive cable from a failed seal in the speedo drive at the gearbox. This is able to climb all the way up and gunk up the inside of the speedo. I had this too, and had to dismantle everything and very very gingerly clean the speedo out.
×
×
  • Create New...