Jump to content
SAU Community

Rb25 Turbo Upgrade, All Dyno Results


Recommended Posts

With so many threads about turbo upgrades for RB25's i thought itd be a good idea to start a thread that shows results only, as the results from various threads are scattered everywhere. Everyone has there own ideas about what power they want so obviously there isnt ONE perfect turbo upgrade for everyone.

Please post your RB25 dyno graphs only and state the following:

-Engine management

-Boost ran

-Fuel used (pump or special)

-significant engine mods (eg cams)

The idea of this thread is to be a quick reference to various turbo's performances on RB25's, not to be a discussion thread.

Thanks

(If this has been done already let me know, but didnt come up one in search.)

Check (if you live in usa): Costco Weekly Ad, or Supercheap Auto Catalogue.

Link to comment
Share on other sites

:werd:

And does someone have a rb25det hi flow dyno result that they would also like to elaborate a little bit more on.

I dug this up from an old thread heres the thread with talk on the hks2535,2540 & 3037.

Click me

And here is the hks test chart for 2510,2530 on rb20det and the rest 2535,2540 on a R33 rb25det.Very interesting and has helped me to answer some of my quetions.All tests are done at 1 bar of boost.

Click me

There is a larger range than that there too with tests done on other cars as well.

Link to comment
Share on other sites

here is my dyno results

mods

3" exhaust

pod filter

10psi boost

safcII

FMIC

BP Ultimate 98

stock standard turbo

We had an idling issue last week and to fix it the boys had to mess with the safc,

after getting the car to idle she ran 285hp but i didnt get a printout so i guess for this exercise i have 273hp

Link to comment
Share on other sites

221RWKW mongrel unknown spec turbo from Rigoli.

The build consisted of:

Arias Forged Pistons 1.0 mm OS (1300)

GTR rods with fresh bolts (400)

ACL heat treated race bearings (120)

Balance, clean and O ring block etc. including straighten of crank and lightening. (1100)

GTR fuel pump (180)

Malpassi Rising Rate fuel reg (120)

Standard head gasket (90)

Hybrid Monster FMIC (700) piping (120) new Mig welder (700)

Autohouse Tsukasaki PFC (secret)

Dump and front combo 3" with Fujitsubo "Jasma" 3" stainless system and racing cat also fitted.

Click Here for dyno sheet

  • Like 1
Link to comment
Share on other sites

Engine management - PFC

Boost ran - 1.4 Bar

Turbo - Garrett GT30

500cc injectors

Bosch 044 pump

HKS EVC 3

45mm Turbosmart External Wastegate

Custom Made Steam Pipe High Mount Turbo Manifold

Z32 80mm Air Flow Meter

HKS 600x300x76 Tube And Fine Intercooler

Custom 3inch Exhaust

HKS adjustable exhaust cam gearstock

etc etc etc

Fuel used - BP Ultimate

Stock Internals

The dyno graph i have is from MAS 04 as i cant find the selectamaz one where it went 324rwkw on a nice cool exterior located dyno.

  • Like 1
Link to comment
Share on other sites

1994 R33 GTS25t

Avcr - 0.8bar

Full zorst

Trust IC

Standard Turbo

Standard Ecu - no tuning or piggybacks

Automatic gearbox

180.3 Rwkw

Good strong power curve :burnout:

This was bout 3 months ago, shes a little different now :)

Link to comment
Share on other sites

not home atm so cant post up dyno

1995 gts-t r33

turbo back zorst with hi flow cat

pod+ cai

hybrid fmic

10psi

stock turbo

stock ecu

optimax fuel

hybrid bov

173rwkw on a 29 degree temperature at 7:30pm lol about 6 months ago was last dyno

new results in a week with power fc, avcr (12psi), z32afm

ben...

Link to comment
Share on other sites

1994 GTS25t

Hybrid TO3/TO4E (high flowed too - back cut ex wheel etc)

CP Forged pistons (8:1 CR)

Grex 1.6mm HG

ARP rod bolts

Port matched manifold

550cc inj and custom top feed rail

Malpassi reg

044 pump

K&N and custom inlet piping (nil AFM)

LT12 Microtech

FMIC

HKS EBC

Full 3" exhaust

The list could go on a LOT longer!

Also now have HKS cams (256 / 264)

Dyno pre HKS cams

Boost - Drops away to make peak power of 299.1rwkw @ 1.3bar

Dyno post HKS cams

Boost - Drops away even worse now! 270rwkw @ 1.1bar

Wanted - more $$$ to get a bigger turbo, run 1.5bar and make 300++rwkw :)

Link to comment
Share on other sites

1995 gts-t

Stock turbo

pfc

gtr fuel pump

adj fuel press reg

3'' catback exhaust

ebc

Pod filter+partion

Small Hks front mount

Slipping stock clutch,leak in header/exhaust gasket.Cant remember what boost it ran...

12:1 afr's

182.0rwkw

:chop:

Link to comment
Share on other sites

R33 gtst

Series 1

Stock turbo

Custom Dump pipe (Seperate wastegate pipe blended in), Hi flow cat manderal 3''

Stock ecu

Blitz LM cooler

8psi boost

K&N panel

Shootout mode dyno dynamics 175RWKW

Leaning out so couldn't rev out

AFR's went to 13.1 so backed off at 4900rpm

Will dyno in jan with pfc, pfc boost controller, upgraded fuel pump/nismo press reg.

This thread is great!

Link to comment
Share on other sites

gcg st.1 450hp high flow turbo . gtr front mount cooler

aftermarket manifold, ces racing 3inch split dump, 3inch cat and exhaust.

link ecu, malpassi rising rate reg.

stock internals and stock cams.

224rwkws at 17.5psi, with more power to come just need new coil before i can run more boost. 224rwkws at 1.2bar shootout mode, dont have scanner to post sheet.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can believe it if you're getting air into the pickup. Cavitation is tremendously destructive for pumps.
    • I think the pic in the first post is another car, and post 7 is OP's car with standard arms and swaybar swaybar swaybar. I can't tell what brand the silver coilovers are, and even if I could I don't know whether the spring rate is OK, if you can find a brand on the shocks and numbers on the springs that might help. Also, if you can measure the ride height from centre of your wheel to the guard that will help with advice too as handling suffers if ride height is too low
    • sadly, pics no work. that car must have spent a lot of time in a cryo bubble
    • In the first photo you posted, the colour of the control arms are the signature colour for Ikeya. Same for the swaybar, signature colour for Whiteline.  I like Hardrace, they also do hardened rubber bushes if your car is mainly a street car.  I like GKTech as well, but they use a lot of rose joints in their stuff so might not be the best choice for everyone.  The system might have been good back in its day, but it's a prehistoric system now. I suspect that most people have removed the HICAS as they want the car to do what they want to do, not what the car wants to do. From what I also understand, it isn't consistent in it's behaviour on track so it's hard to trust the car/know where its absolute limits are for track use.  Having said that, I think the HICAS eliminator kit was the first thing I installed when I bought my car. I don't personally have any experience with the HICAS system on a race track.  
    • Thanks for the info. Didn’t know I had aftermarket control arms already? Will talk to my garage. What brand would u recommend if I want to play around with my camber more? I would think my camber is around stock level right now or more negative now due to lowering with coilovers. I will be lower her again 1.5 cm to get some more.    also why does everyone like to remove the hicas system? Is it because most don’t work properly anymore or ppl just don’t like them. Mine is functioning as it should be right now.    thanks for the good info 
×
×
  • Create New...