-
Posts
643 -
Joined
-
Last visited
-
Feedback
100%
About 33SOM
- Birthday 22/12/1982
Profile Information
-
Gender
Male
-
Location
Biloela
Profile Fields
-
Car(s)
BNR32, Prado
-
Real Name
David
Recent Profile Visitors
5,823 profile views
33SOM's Achievements
-
ATI Balancer Powersteering question R33 GTR
33SOM replied to MoMnDadGTR's topic in General Automotive Discussion
Hicas is long gone. It's not as heavy as it is when HICAS is causing the issue. -
ATI Balancer Powersteering question R33 GTR
33SOM replied to MoMnDadGTR's topic in General Automotive Discussion
I have a ATI917752 with the power steering pulley on my rb26 (32 powersteering pump and r34 crank) and the steering is heavy. Anyway to resolve this or should I just replace what I have? -
g35-900 vs g35-1050 vs 6466
33SOM replied to Scratched Skyline's topic in Forced Induction Performance
I have a 6466 on my built 26 but haven't got it tuned on e85 yet as I'm worried it will brake as I don't have a brace or grout. How long did it last? Motor was built around 2000kms ago (8 years ago from memory). I wasn't aware of block braces at the time and never intended on putting a 6466 on it.. -
33SOM started following Seat belt extender thingie , Ati Harmonic Balancers For Rb26 In A Bnr32 , R33 gtr gearbox upgrades? and 3 others
-
Ati Harmonic Balancers For Rb26 In A Bnr32
33SOM replied to AtomicBomberMan's topic in Forced Induction Performance
Sorry for bumping an old thread. Has anyone else's steering gotten heavier with a 1000hp ati balancer installed? -
After a lot of reading I'm leaning towards a PAR gearset. Just gotta work out if I go syncro or dog...
-
Waiting for a reply from them
-
Greenline.jp Os giken
-
So an Os gearset over a Par set is the recommendation? Probably a dumb question but looking at my attachment which one should I order? The heavy duty input shaft or the holinger type? Cheers Edit: I don't have a clutch yet so will probably go with the Holinger type and an R3C
-
I have a 6466 on my built 26. Twinscroll .84 rear. What should I expect to make on a 98ron tune? Not ready for e85 yet... Made 400rwhp @10psi while running it in 2 years ago and I haven't been bothered to return to the dyno... Happy to run all of the boost in the world Cheers
-
Heavy Steering And Hicas Warning
33SOM replied to glenndrayton's topic in Suspension, braking and tyres
Thanks for the reply. There is probably nothing wrong with my speed sensor (I just assumed that the reading fluctuating so much indicated a problem) and my Hicas issue is most likely something else. Cheers -
Heavy Steering And Hicas Warning
33SOM replied to glenndrayton's topic in Suspension, braking and tyres
I'm trying to figure out why my steering is heavy at low speed. So far I have figured out the speed out of my cluster is fluctuating around 10kmph or so (looking at the software on my link ecu) Also measuring the yellow/green wire at the Hicas ecu the volts are fluctuating at a constant speed. Could this fluctuating be causing the hicas to stop adjusting the valve in the steering rack? Glen did you have to replace the whole cluster or can the speed sender be replaced on it's own? I tried many times to get the car to enter diagnostic mode but it wouldn't do it.. Cheers! -
So the FX-R 3.0 is still the one to use?
-
There is about 5 mins taken out since the original upload
-
Seat belt extender thingie Hi all, Chasing the seat belt extender that attaches at the top of the seat belt so I don't have to reach around so far (getting old..) Car is a 32 gtr. Cheers