Jump to content
SAU Community

Craved

Moderators
  • Posts

    17,563
  • Joined

  • Last visited

  • Feedback

    100%

About Craved

  • Birthday 20/04/1982

Contact Methods

  • Website URL
    http://www.cravedcoatings.com

Profile Information

  • Gender
    Male
  • Location
    western Sydney

Profile Fields

  • Car(s)
    R33GTST +more
  • Real Name
    Chris

Recent Profile Visitors

13,110 profile views

Craved's Achievements

Grand Master

Grand Master (14/14)

  • First Post
  • Collaborator
  • Posting Machine Rare
  • Conversation Starter
  • Week One Done

Recent Badges

7

Reputation

  1. lobster is very time consuming, you could get an alloy donut with a tight radius - such as http://www.jntperformance.com.au/index_g3.html?itemId=13665772&catId=395407 and have someone modify yours or start again. clearance wise im sure most would prefer to have the car to work with.
  2. clean your AAC and IAC valves, then reset the idle via the idle adjustment screw
  3. yeah, you can see the holes in the black post in the picture.. one has the silver locking bar in it for max height. at the base of the arms. just a 20mm rod of steel through holes, other position is half height
  4. that picture is from http://www.engineeredtoslide.com he uses double spacers under the lift pads to get extra height, so would need to jack it up first my cars all go on fine, but my 33 is 100mm legal height
  5. use to be sold by levanta in QLD but cant seem to find it on their site.. that Happ one you posted Dan seems a bit better as the max jax only has 2 locking locations
  6. ive got a maxjax like below - full height with the bonnet up on the 33 is 2400 cant walk under it, but a stool with wheels is easy enough, 240v and uses threaded anchors not dynabolts to make it portable to some degree. atleast pack it away when not in use
  7. if the original wiring to the pump is used as the trigger, which is in the boot, then all one needs is the new 12V direct feed to the relay then the pump. Changing to a fused relay, the pump is fused nice and close to the end application - and can double as a kill switch without opening the bonnet
  8. that pipe is an external oil drain from the head, due to the additional oil from the VCT system on the 25. you'll need to find a way to keep that, or T it into the oil drain from the turbo
  9. another couple of steps.... test fit of the new dump pipe worked perfectly, so rather than remove it to finish the welding i thought i'd dummy up all the lines for the turbo. New hard line is run around the front of the motor and will connect to some new -8 fittings in the turbo and hardlines with tube nuts. Old drain still works, just needs to be shortened slightly and the old oil line fittings in the block worked great. just need another metre of the -4 teflon braid to move the turbos oil filter up into a serviceable area. getting all this sorted out, means i can head straight to ceramic coating everything the next time it is removed and the dump pipe is sealed up with the TIG.
  10. Ended up flat chat last week, so it got delayed again. New dump is almost completed, just need a long die grinder bit to clean up the inside of the merge a little, then i can weld the rest of the wastegate dump up. Still unsure whether i'll need to run another vband on the WG dump to assist with install, got one on order but ill test fit it without and see how much of a struggle it will be. Also removed the turbo's water return from around the back of the head, going in favour of a solid line running around the front of the head ready for the 26/30 install. Removed the water feed from the plenum/fuel rail completely and blocked it off behind the thermostat.
  11. thanks Duncan, shop was a huge undertaking and a big step up - 7m long oven ready for doing full chassis etc ETA? haha that depends on how busy i get, hoping to have the new dump pipe finished off this week, that could get her back on the street if i just leave it at that. but that never happens, besides, once shes up on the hoist i keep finding new things to do/fix/improve upon - having a hoist is both blessing and curse
  12. next job to complete at this point is the radiator shroud for a thermo fan, this one is incorporating a cross over pipe within it for a legal spec catch can arrangement on the drivers guard that will feed back to the air intake without running a long ugly hose across the engine bay.
×
×
  • Create New...