Gareth87

Just checked it out, The shipping is nearly $200 AUD. I'm sure a local supplier on the GC will have stock of genuines. Thanks for your reply though.

Hi all, Looking at upgrading my LS1 coils as I'm just about on the limit with them. I want to go with the IGN - 1A coils but I'm seeing a few different brands. Gut feeling it telling me to go with the haltech version. However, I see Aeroflow advertise them as well and I don't want to end up buying the wrong part and ended up with wasted dyno time. Can anyone shed some light on it? Thanks in advance.

Very nice! Hopefully it fits in the tunnel ok..

All starting to come together! Can't you use the RB adapter kit rather than making one for the FJ? Should just need to machine the top holes to suit the FJ.

Definitely keep the thread alive mate. Following with great interest. Where are you located. Would be keen to check it out as you progress. Yes.. the Can performance GCU seems to be the go. A lot more sorted the the HTG so I hear.

I've looked into this and the answer I came up with was that the potential risk of restriction and causing engine damage was too much risk. Haha. It's already 40yrs old and people look at me weird when it's cranking over for ages before starting.. I'm currently looking to see if an assembly lube pump hardwired in with work. Can't find the right pump yet..

Bit of a task to do every start up.. lol No, pump is too high and lower control arm in the way unfortunately. If the pump is small enough and doesn't even need to do much pressure. Just needs to fill the lines. Finding it hard to locate something to do that job..

Been having this problem for years and I'm over it. Have an FJ20 with external oil pump. The pump is mounted slightly higher than the sump and it has a -10 oil feed line to the front cover where the internal pump used to be. Each start up, it rattles it's head off until oil pressure comes up. My solution is to set a start delay in the ecu until it sees oil pressure. Problem with this, it takes ages to start each time as the longer it sits, the more prime it looses. I looked at an accusump as a solution which would of course work, but are there any other fixes? I've been looking at small electric oil pumps that i could fill the system with first but nothing seems specific for the problem. Any suggestions would be great. Thanks

Sorry for the slow reply.. I know exactly what you mean about using the steel in the strongest orientation. That was one of my considerations for going with such a chunky piece of steel. I had to double check the photo of the deflection and yes, it does look like its bowing a lot.. but if you look very carefully, that's actually a shaddow. It was barely any perceivable deflection. I'll measure it with my laser next time it's in the air. As for stability, it's rock solid. I lifted it just off the ground and gave it an earthquake test before going higher. I don't take chances with stuff like that!

Problem resolved. Thanks for the help everyone. Went with 2 lengths of 2.5m steel 125x75x6mm to use to reach the lift points. Works perfectly. Just need some caster wheels on the steel sections to move them into place a little easier. I can lift a standard height car to 2m and my van to about 1.5m before hitting the portal frames.

Ok. So I've taken everyones input and come up with the best option of a length of steel.. something like 100x75x3mm and sitting the rubber blocks on top of it. Its 1950mm between mounting points on my van ans less on my datsun. So the overhang is going to be less than 500mm over each end.. but being 1 length of steel and a large contact face in the middle. It will be certainly safe enough. I'll pickup the steel tomorrow and post some results. Thanks everyone

Yeah exactly! Great idea. I'll most likely have to punch a hole through the face of the lift to get a fixing. However.. the I beam scenario might be ok as there is only a small over hang either side of the lift face needed to reach a lift point. Need something like this but length ways Thanks for the input everyone.

Thanks lads! Been a work in progress. Had the FJ in my car since 2004. As for the blocks. I actually have those, but the problem is that the lift face doesn't reach any of the lift points under the car. I need steel arms or something similar to reach under the car like a conventional 2 poster hoist. Need some ideas on how to achieve this safely and neatly. Can't find anything out there..

Hey all. Got myself a brand new in ground scissor lift, but I'm struggling for mounting points. The lift position doesn't quite reach my lift points.. and I'm definitely not sill lifting. Has anyone made up some bars to attach to the lift tops or alternative lift methods when using a scissor before? Thanks.

Funny this thread has resurfaced.. I am going to do a log recording when I get a chance and I'll take the front bar off vs standard. I want to see if the added airflow changes things much. If so, I can put at least part of the problem down to airflow.