thanks

Just getting my head around the offset required for an R34 GTT. I've searched a few topics, got some ideas, but others tend to run different widths than I want to.

So I was thinking of getting a set of Lenso D1R's in the following size:

Front 18 x 8.5" - +35 offset

Rear 18 x 9" - +32 offset

Tyres i'd organise later, but probably something around 235 on the front and 255 on the rear.

I'd prefer NOT to get my guards rolled. Currently the car has stock suspension, and If I do lower it a bit, it'll be only with slightly lower springs, maybe 2cm lower... not sure on that yet.

Anyways, would that combo work ok?

Looking to get SSR SP3 or SP5 for my R34 GTR in 19x10.5 and looking for an offset the same as this.  My guess is +12 but does anyone know the car or have a view?

Cheers!

I have looked everywhere...or i may be missing something. With all the Taiwan/ Chinese rep products, i've been real skeptical to buy a low mount rep fiberglass spoiler. Was looking more at Carmate and unique autosport import as they have the low mount options, but with inquiry, they are from china. Am i better off going through Aliexpress?

Can anyone add their 2c on their fiberglass mould? Or can someone point me in the right direction of where to search for something similar? Willing to add the extra $ for a good quality product

I'm also looking for a carbon wing + caps (willing to buy these separate as i've had no luck finding a low mount combo with the carbon bits) 

Looked into carbon addictions but i've read nothing but bad things about their service and other carbon fiber products.

Fitting on a GTT 34

My diffuser (not genuine, carbon fibre, came with the car when it bought it, I don't even like the carbon fibre look) is completely smashed.

Whats the difference between a genuine front diffuser compared to, lets say a JSAI front diffuser (fibreglass)?

Is the genuine more durable compared to the fibreglass one?

Trying to justify if it's worth buying a genuine diffuser.

Also, out of curiosity, what diffuser do you guys run? Genuine or a copy? 

Thanks in advance guys!

So I might just be a bit slow but wanted to check how these pedals are supposed to be installed. My R32 brake and clutch pedal are held on by a rubber portion and the accelerator by a clip. I got a set of old Nismo pedals that came with little screws/nuts but wanted to know how these are supposed to be mounted. Am I supposed to screw them on top of/into my current pedals? I don't see how they would be installed as complete replacements with the hardware that came with them. The R34 aluminum pedals on the other hand seem to be direct replacements as they look like metal versions of the regular rubber ones.

Recently got into a sticky situation with my car and I'm in the need of new corner lights. The thing with my GTS-T is the previous owner put on the GTR hood, grill, headlights, and bumper.  I can't really tell if the fenders and corner lights have been converted so I'm not sure if I should be looking for GTR or GTS-T Indicators. Here's a pic for reference.

Also has anybody seen or heard of anybody besides ZLED that converts corner lights to LEDs like this?

Hi guys,

I'll start of by saying I'm no professional, really I'm doing this just to improve my solid works skills and hopefully end up with a replacement set of centre caps I can use. But I am planning on 3D printing a set of Ray's centre caps to fit lmgt 2's ( may fit 1's aswell?) as anyone with the caps know the plastic gets brittle and the mounting tabs snap off! I have seen sets go for over $600 in good condition... But really they are still 20 years old . All going well the final product will be made of abs plastic ( unless anyone has an opinion for otherwise?) yet to see wether there will be the ability to colour match to the originals otherwise more than likely black , cost I am unsure of yet.... I was going to see if there is any interest first so I could enquire for x amount of caps and see what happens but hoping around half the cost. All the dimensions and measurements are being taken from a genuine centre cap and I will get a mock cap made up first to ensure fit.

Is this something anyone/ones would be interested in? Nothing final just a gauge of interest at this stage.

Thanks!

Hi guys 

I'm busy trying to restore my R34 GTT to immaculate condition. I want to replace the rubber seal that goes on the windscreen at the bottom. I looks dried up from the sun and caused it to warp and break. I've attached photos. I would like to know where I can get my hands on something like this as I would like to replace it.

Also, on the driver and passenger window upper seals, there seems to be a line of glue that was left behind from previous owners putting wind deflector/visor guards on it. How would I get this off the rubber? Also, there seems to be a huge gap between the rubber and the frame. Is that normal on R34s? Could I just replace it? And how would you restore all the rubber seals so it looks brand new? 

Thanks 

Using a 6V lantern battery, these are the results.

Factory lens: about 30 or 31mm

ZKW-R: 22.5mm

FX-R: 24mm

Q5-R: 28mm

Here is what the Q5-R looks like installed.

Here is comparing Q5-R with cheap halogen H3C bulb to a cheap aftermarket HID installed in a Saturn Sky.

Very good cut line with the Q5-R lens.  Now I will see if I can find someone with H3C sized HID to try on.

Looking at getting some N1 side skirts and trust rear pods for my R32 GTR. I take it that you can no longer buy the genuine product new and finding them second hand seems very difficult as I have seen no one selling in a long time.

Is there any GOOD non genuine N1 skirts and trust rear pods that are very high quality that you would recommend buying from. I don't mind spending the money if it means that I get a superior product. Any help would be great.

Thanks

I was hoping I could find some help here in locating them. Mine cracked pretty badly. I circled the specific parts. (Not my car in the picture)

I've found threads for what size is the best for r34 gtr skylines but found a few different answers for this question. I've just put down a deposit for a new set of lmgt4 wheels. I'm undecided which size would be the best 18x10.5+15 with 275/35 or would 18x9.5+12 be better as it's closer to stock size? Just want to know if I go with 18x10.5 would they rub? Some people say yes some say no. I'm not using the car for track which im told 18x10.5 would be fine. The car is currently stock height, am going to get  coilovers as soon as i get them.but yeah Just looking for any opinions/experience that anyone has had with these sizes. Thank you 

Just picked up my r33 gtr a couple of weeks ago. I wanna know what kind of kit is on it? I think the front is a 400r style one. No idea what the skirts and rear spats are? The spats seem a lot larger than other ones I have seen.

At first I wasn't too keen on the sideskirts but they are growing on me. 

Any ideas on what I should do next body wise? Was thinking of keeping the front bar and find factory rear spats and factory sideskirts. 

So my question is, has anybody tried or seen something similar on an R32 GTR?  That is, accent striping on the front lip, side skirts, and rear bumper. My imagination says it could work nicely but then again my imagination often betrays me. Throw up some pics if you got them. Might even fiddle around in a Forza livery editor or something!

Both serious and not so serious replies/help encouraged, thanks  😂

I am in the process of figuring out a front bar for my R32 GTST. I am aware that GTR front bars can fit with modification, but I am not wanting to do that, and they are rare as hens teeth where I'm from (NZ).

What are your thoughts on the front bars (GTR-ST) from JSAI and KMAK Aero? GTST size but R32 shape (vents, grills, bottom lip etc). Has anyone had any experiece with either?

https://www.jsai.com.au/product/nissan-r32-gtr-style-front-bar-to-fit-gts-t/

https://www.kmakaero.com.au/r32-skyline-gtr-st-front-bar

@ThePurpR34 here, so I purchased this R34 GTT earlier this year. I have essentially been tackling the things the previous owner did/did not do to better fit the car to my standards.

According to him it is a front gtr z-tune bumper and z-tune hood YET clearly the fitment is not proper. As you can tell from the picture, the grille part of the bumper seems to be a straight line whereas the hood curves up for the grille area creating the gap.

What kind of hood will fix this fitment issue? From looking it looks as though an oem gtr hood would fix?

Never really introduced myself on these forums, lots in the future for this car so I'll most likely create a thread once it's re-wrapped. Thank you guys for the advice and phenomenal amount of knowledge around these forums!