Long and low

This is with standard shocks and cobra lows. I have bc gold to go in. I'll be pissed if they are no better.

That's good to know about the break lines. How mong did it take you to install the bc's? I have a set for sale but I'm always tempted to just put them in

Drying out under the carpet after the new windscreen was leeking

Sadly shes now up for sale

Fresh out a paint. Now to start moding again *custom white with ferry dust in it. Can't wait to finish and get some good pictures.

Aliexpress http://s.aliexpress.com/vmYN7BFJ?fromSns=Copy Had to cut holes into the panel to wrought the light. It's too long and to attach you need to buy double sided tape and I drilled holes through to use some wire to make sure it doesn't come off.

Will look much like this just tidied up. I have to clean up the clear lenses to go over the front to seal it. The light bar is custom from my company I had. They are about 4 times brighter than the stock high beam. The strip across the top is daytime running light and indicator in one. The halos are park lights so will come on with the auto headlights. The flashing lights in the sides are just for when the cars on show. It is very hard to recreate the mounting points for the stock HID as I have cut 2 of the 3 off to fit the light bar

That's just for use while the cars on show. I'm not going to use on the streets

It's a massive job. All parts are from aliexpress 20180412_160835.mp4

Making some progress with my headlights today

I had my car on the hoist and took the opportunity to get a picture of my exhaust. The x pipe was taken out to help reduce drone. I need to sound deaden the boot too. It's 2"

My car was keyed and tyres let down. I am insured so it's getting a full respray. I will be doing a few mods and surprises while it's off the road. Watch this space

Connected my phone to the factory Bluetooth. Phone controls on the wheel work too. Noticed the voice recognition understands English but you need to know the names of the menus....... Anyone got more experience?

I have a set of BC gold adjustables to go in. Seems pretty straight forward to put in. I'll be doing it in my garage on my own.

Good improvement. I couldn't bring myself to sell my Autech rims. They are just sitting in the garage "in case" Spot the Easter egg....

I could sort a deal out with Springs if your in nz? I'm going to put in adjustables in the new year 19x9.5 +22 -cobra lows

Where did you get your sound deadening? Cost? I'll hopefully get a vid up of my exhaust this week

Currently customising some headlights. DRL and LED high beam. And have adjustys to go in after Christmas. Pm35- axis Autech. 19x9.5 +22

Oh i dont have a photo of that unfortunately. Sorry so if it's like yours what model does it match? G35? Also have you tried to put in a double din headunit?

So mine is a rwd so is it the same at what you have said? 350 will work but watch the weight in the back?

Very helpful. Thanks heaps. I would love to see the setup in "MrM35" Stagea. I have only seen exterior stance photos?

I went custom, 2 inch from the headers. 2 separate pipes with a resonator and muffler. Had to remove the X pipe due to too much drone in the cabin. So each side has its own exhaust now. No cats... Love New Zealand

Still hunting for air ride suspension. Do 350z kits fit? Wheels are 19" 9.5 +22 had to roll guards but the kit hides that

I am interested in the suspension parts also. Looking to move to airride?

05 M35 Stagea Need help with suspension in my 05 Stagea. It's a Autech, axis, 350. Rwd I can't find the answers I need and the posts are like 8 years old... I would love to put an air ride kit in it. But I suffer the same problem listed in the old posts on here.... " A Nissan what"? MrM35 if you see this I need you lol. Can I use a 350z kit? What can I match parts to? Thanks in advance.