"G"
Members-
Posts
43 -
Joined
-
Last visited
-
Feedback
0%
Content Type
Profiles
Forums
Events
Gallery
Media Demo
Store
Everything posted by "G"
-
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
You started it. Nice attitude & cursing, but complains about my attitude after 😂 gtfo. Don't be such a salty vag because you got trolled. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Typical aussie trigger sensitive snowflake. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Triggered. I baited you right in to that one. 😂 Secondly I do not see anything you drew in paint. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Will take a look. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Still waiting on that diagram Mr. Electrical engineer. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Draw me something like this with the nissan wire colors. I want to use a new nissan thermo switch. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
-
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
mines ecu. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
I don't see your diagram. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
I deleted my air con, everything under the hood. Now it won't activate at all. I want to create a stand alone circuit that activates the fan at 194d. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Nope, it won't activate alone. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
I'm pretty sure it won't activate if the ac is not on. Even if the thermo switch reaches 194 degrees. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
Draw that out for me in a modern comprehensible schematic. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
That would be awesome! -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
I meant I want it to work with the thermoswitch as the activator. So i don't have to push any buttons. -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
hmmm -
R32 - Have Your Overheat Fan Turn On With Your A/c
"G" replied to Cubes's topic in Tutorials / DIY / FAQ
I wish I could get it to work with no ac installed. -
Did you check the 10amp ecu fuse?
-
I'm pretty sure the cel should illuminate with the ignition on, but before starting. Mine only illuminates while cranking. Something is going on with the wiring for sure.
-
Does this seem expensive? https://www.obdinnovations.com/nissan-consult-bluetooth-14-pin-ddl-diagnostic-interface-v2-3/ Is there something else out there you have had good luck with?
-
I'm also using this ddl adapter https://www.obdinnovations.com/nissan-consult-usb-14-pin-ddl-diagnostic-interface-with-ftdi-ft232r-chip/
-
Turns out the ecu fuse (10 amp) was blown. Now I have a cel while cranking. See attached video. Is this normal for it not to turn on while ign is on? Also i still can't get in to the diagnosis mode to read codes. I am arcing the 2 pins for 2 secs. If i have no codes is anything supposed to happen? I still can't get my laptop to connect to this program >> https://conzult.com/ Is there a better software i should be using? celv.MOV
-
Ok. I removed the mines ecu and installed a stock ecu. Same issue.
-
Previous owner in japan seems to have disabled my cel and I can't figure out how to fix the issue. I get nothing when I turn the ignition on and when I start the car. Checked the bulb in the cluster, it's fine. Checked continuity from the bulb trace to the ecu and that's fine. #32 orange black wire. The ecu seems to not be sending a signal to the bulb. Tried activating the codes via the consult plug and that doesn't get it to light up either. On a side note, i can't get my laptop to connect to the ecu either. Using datascan. I am literally at a loss.