GTR1993

They made in china. They might be finished in america but there is so many forgings all coming out the same factory.

Didn't you use eagle rods! just having a dig

what bolts on the rods you using?

Just a question does the RB26 500 hp balancer mate up to the RB26 power steer and RB26 AC compressor when they are bolted onto the RB30 block?

If you can spin them fast enough you wont need to do it for 2 minutes they will blow before that. I have helped prepare holden 5L motor for burn out comps and it took 3 motor rebuilds to get it somewhat right, and its coming out again to check it after its last burnout. It has drains from both rocker covers, a oil catch can that drains back to the sump, a breather in the valley so air doesn't have to push out the rocker breathers (not much use for a skyline) moroso accumulator and also an oil pressure sender that cuts revs to 2500 when oil pressure drops below 30 psi or so. Large oil cooler with thermo fan and hienergy sump, it takes close to 10L of oil.

I know this is late but was there anyone that pulled out, i would gladly take one of these? Cheers

Hey i have a bride brix seat for sale, it comes with a S13 rail, it has had the one extra hole drilled in it so its now fits S13, R32 (i think this also fits R33 s14 but would have to check) It is in very good condition, no rips or tears. I only used it for 6 months then pulled it out and went back to the standard GTR seat in my skyline. Selling as i have bought a fixed back full bucket seat for track duties. After 750 ono pm here can ship, i get good shipping rates as a friend has accounts, but it is a large item will still be a bit.

Yea i thought about that, ill try this way and if its no good i can always change it to the same muffler that you are using, but they were cheap so i thought why not.

I actually bought 2 magnaflow mufflers the other day (the center muffler im using center in center out) and they were $310 each! Im going to try this if its no good ill get the custom one, but i had the car int he air and should fit fine.

Have you run a car up in 3rd and 4th? It really makes no difference to power at the end of the day.

update us what the price is gonna be, im happy to ship mine to them ( i have a spare here)

they are decent, i used the for my gtr diff too.

Also in for this answer. I have a feeling it will end in buying lots of not so cheap parts from nissan

Hey i have a gts4 sump here (same as gtr) that im cutting to fit my hi octane sump extension to and also installing my cusco lsd into it. There are four or so small holes that let oil drain from the back of the sump into the main part of the sump where the pick up is, but i cant drill them out as the tube that houses the drive shaft that goes to the left hand CV is in the way. Does anyone know if this can be pressed out easily? Cheers

Its chris milton engine developments, adelaide engine developments are different and located like 10-15 km away. for 1500 hp id be going dry sump for sure....

Im using the hi octane setup, hopefully its good...

need a lot more then a t51 to go for 1500 hp i recon, spl be good for maby 1100hp ish definitely palumbo he was relative of guy i went to school with

Just get it re gassed, depending how far you want to get into it will depend how much u want to spend. Just get it gassed and see if it stays working, because there is no point replacing the receiver drier if you leak gas out a seal or a rubber pipe and need to get that fixed.

AED would be darren palumbo

Actually exact measurements of the center muffler would be awesome, saves me from guessing under the car. Cheers

Oh no rush man i dont plan on doing it tomorrow or anything, also im in adelaide but thanks for the offer

I gave them a ring and there factory is in bathurst, s i think they are the same place. If you can check some time it would be greatly appreciated as im going to do the same setup as your car.

On my motor im going for 2 thou on the mains, you will get lots of different answers and reasons, i build them a little looser. Friends sr20 we got 2.4 thou and its fine, select correct oil weight and you should be fine.

picture of the boost controller

I see in Adelaide there is a shortage of E85 and most the servos were sold out!