Single

Hi, interested in the crank and internals. can you send me a message and some photos? 0420971976 Josh

Good Morning, I'm trying to get the tooth count and sizes of the ABS disc as i'm using a VSS in the original position and need it for my calculation. I'd do it myself but currently my car is in a different state. If anyone has one out and can help me with a couple of measurements i would be cheering! or if there is some details that i can't find and you could forward them to me i would be stoked. Josh Picture attached so you know what wheel i'm talking about.

Hi, Looking for an rb26 head complete but minus the hot side (no turbo's) needs the plenum, acv, iirc (what ever it is) rockers etc. I don't need (if it makes it any cheaper) cams, loom, coils, and injectors, cam cover or rocker valley cover. Can be parted, as i'm happy to assemble. also looking for an Tomei oversized oil pump for an rb. let me know whats about. Josh Sydney 0420971976

Would also like to know

I got 383rwkw on just 18psi with 98.

Bump

Pm'd

Hi, Looking for a exhaust manifold preferably a 6 Boost as some are 25/26 compatible, but am open to other makes Must be: High mount Steam Pipe T3 flange Other Preferences: Single or Dual gate i don't mind. Prefer Twin Scroll Josh 0420971976 Sydney (would like pickup as i could inspect but am happy to pay postage)

So for anyone looking for this information later: I emailed around and a shop in the US has made them and has a couple in stock. I have placed and ordered one, and will keep everyone updated. The z33 CD009 (2005+) are far superior to the rb25 boxes

So i am doing some research on the Z33 gearbox (revised model with better Synchro's) or Z34 gearbox mated to an RB (all models) Has anyone on here successfully done this conversion? If so, where did you get the Adaptor plate, or did you do a Cut and Shut job? I have found numerous plates for all different engines, VH/VK/JZ's/SR's and even CA's but nothing for RB's My 26/30 is pushing over 380kw on 98, and i want to change to E85, but i doubt the RB25 box will hold much more while i'm slamming gears mid drift. Can you guys give me some input into the setups? Cheers Josh

Gents, I have a series 2 rb25det for sale. Complete longmotor with: R34 Thottle body Starter motor. Cas, harmonic balancer etc. No Coils. Also comes with a new set of ACL Racing bearings(full kit) as the engine needs a rebuild. No accessories unless mentioned. $400. also have a brand new RB25 Exedy clutch. includes bearing and cleaning lube. paid $420 and is still in the box so looking for $400. all located in the Sutherland Shire Josh 0420 971 976. MSG or PM during business hours please.

Gents, looking for: R33 R200 diff. any ratio higher than 4.0 (4.08, 4.11, 4.3) can be locked, shimmed or will even buy a 1.5/2 way if its the right price. needs ABS needs 5 bolt half shafts sydney preferred Josh MSG me or PM 0420 971 976

got one with all arms in but no bearings

mate i have an rb30 sump and pick up as well PM me

mate how did you go with this? which sensor did you end up getting? i'm exactly the same, i want the gauge to be stock.

Nissan Silvia S15 Full Backyard Conversion RB26/30DETT Block honed bored and fully forged. 8.1:1 Compression Extended Crank collar fitted, ARP bolts/studs throughout Nitto Oil Pump, oil restrictors fitted, head oil drain. Nismo Water Pump, thermostat and oversized R32 GTR radiator HKS 2530's with braided lines HKS Cam Gears and 264 Cams, Tomei cap studs Trust/Greddy Suction kit Fuel lines, billet rail and 1350cc injectors Haltech Platinum Sport 2000 inc. 3 Bar Map Sensor, Boost Controller, Dual Wideband 02 Sensors Upgraded 100x300x600mm intercooler LS1 coil packs twin 3" into 3.5" straight through exhaust Heavy Duty clutch, Flywheel, Nismo slave, Pivot and braided lines R33 RB25 Gtst gearbox Custom 3" Tail shaft. not to sure about the diff at the moment but i think it is a stock JDM S15 3.692 ratio Made 377.7rwkw safe run in tune. will upload Dyno tonight

interested in a swap? I've Pm'd you

Guys Has anyone got any updates as i'm going in 2 months and of course i'd like to come back with a bunch of goodies. I'm flying into Tokyo and will also be around Osaka at some point, i do have some time and money to spend.

stuff still for sale overflow bottle $10 (small crack at top, could be sealed easily) front and rear swaybars stock s15 $10 stock snorkel with AFM and Pod. s15 power steering pump $100 stock cast iron manifold $80 stock water and oil lines, banjos, washers everything ($50) R32 GTR cut loom $70 2 rebuilt steel wheel N1 Turbos. $300 charcoal canister and lines $10 ORC twin plate clutch, suit rebuild, 5 speed sr20 one $200 GT28R, straight bolt on for S15 asking $100 make me an offer core is blown. 5 speed sr20 gearbox speedo $60 RB30 full ACL race bearings asking $100

mate, Japanese goodies on your car are a nice treat. i've had plenty of different wheel nuts and to this day nothing beats my Work Wheel nuts. Cheap ones of eBay, yeah they look good this week, but the colour fades on them, ive seen them even break because they are a light cheap aluminum. In regards to using lightweight aluminum wheels nuts i would only look at the good brands. And good Wheel nuts with locks are a lot less common for people to have the Lock socket unlike the cheapies. Sorry its just my 2 cents, as by the time you buy 3 sets its the same price as a Jap brand

This will be good! i think Nissan at Bathurst again will be good, i think it will turn a lot of Ford and Holden fans.

Guys, just looking for a RB30 or RB25 sump I'm in south Sydeny Area, cheap and or free. dints are okay by me, as im cutting it up. Josh 0420 971 976

dude do you have stereo brackets?

my rusty old tongue just made 412kw... have a crack at that with the 25...