manifold5149

Hi mate, Im out in Berwick however motor is in dandenong. motor was built to handle upto 450rwkw As we were taking out the motor somehow one broke, not a big deal could have them replaced myself. Was built and then sat around for a while a just never ended up using it from then on. More than happy for you to inspect.

Hi everyone, I have the following up for sale as i no longer need it. As far as i am aware it only completed a few Dyno runs and not a cent was spared. The following is what was done: RB25 Motor Ross Racing Pistons Engine Gasket set incl. steek head gasket set Race Series Big End Bearings Race Series Main Bearings Welsh Plugs, big and small Serviced Cylinder Head Port and Polish Cylinder Head Machin block deck surface, balance crank and linish, balance pistons, balance rods, machined flywheel, removed aluminium plugs and replaced with steel plugs total cost when everything was done was over 6K (i have the reciept) $6,384.84 including labour etc Im chasing $2200 firm. Anyone who knows about building engines would see that the racing pistons costed 1300 so trying to get rid of it cheap. Any questions please ask. (as far as im aware it will need new oil squirters) thanks, Tom

SOLD

Hey mate, if it could be organized no worries. I'm in berwick. Msg me your number if you want more photos.

Trying to sell all together first. Will let you know

if you need any more pistures feel free to ask, it wouldnt let me upload anymore. thanks,

Hey guys, I have to following exhaust system up for grabs which i had on my R33 Skyine. It is as follows: 3"Dump pipe-> 3 1/2"catback-> 4"from hotdog-> back to a 5" HKS cannon. i believe the dump pipe is either Blitz or Apexi however cannot really remember now. the cats have been punched out and it is quite loud but sounds very tuff! The only marks that are on it are displayed in pictures below mainly due to it being on a low car otherwise in great condition just needs a clean chasing $450 ono Pick up in Berwick Area. thanks all.

Bump. 1300. No use anymore guys.

Hi all, i have a set of Rays Engineering Volk Alloys for sale 8ïnch front and 9inch back. fantastic condition however the tyres are not the best due to them rubbing on the side of my gaurds. i have attached some photos, including sizes etc. chasing $1500 or closest offer. feel free to get in touch, there currently sitting in the shed so need them gone. item is located south eastern suburbs melbourne tom

Hi guys, Moving to Queensland this is the stuff I don't want to carry with me. Prices should be cheap enough. This does not reflect the condition. All of the stuff is good and working. I just want it gone. Call Mark on 0403151598 Nissan 4 pot front brake calipers vgc $120 Slotted Front rotors to suit above. We're five stud and have been professionally drilled to four stud as well so could go on either Nissan 5 stud or 4 stud too. Plenty of meat on them. Vgc $100 Greedy oil cooler kit suit rb or ca motors. Came off gtr. It's the nice one with the filter relocator and thermostat bypass for when oil is cold. Cost an absolute packet when new. Vgc $400 S13 4 stud space saver gc $20 Z32 afm $150 180sx rear hatch panel good glass. $40 180sx rear boot divider. Hard to find. $50 S13 180sx manual conversion set up. Clutch pedal, brake pedal, slave, master and lines $150 Sr20det parts motor. Complete minus cams. Suit rebuild $300 Sr20det gearbox. Syncros are shagged but I'm pretty sure all the gears are there from memory. Suit rebuild $100 Ca18det gearbox. Works fine, just got to get rid of it. Bit of surface rust on input shaft from sitting round. $200 Ca18det greddy trust turbo manifold. Big power manifold. Suit external gate obviously. Brand new. Cost me a fortune years ago. $300 Ca18det xpower cheapie manifold Ca18det 550cc injectors $150 for 4 S13 6bolt LSD good condition, my spare. too heavy to take! $100 S13 full front and rear suspension. Facotry coils etc. Everything but the actual subframe. Call me with what you want. It'll be cheap. R33 rear hicas lock bar. Brand new. $40 S13 180sx air con set up. Complete and was working before we pulled it out. Compressor, condenser, hard lines Etc. $150 Also have an s13 vented carbon bonnet. Small amount of damage to front left corner courtesy of a stray tyre. Solution would be to fix and paint the edges Matt black or use it as it is. $300. Bargain. It ain't that bad. I've had wrecked 2 complete s13 so I have heaps of little stuff lying around. Call me if you're chasing anything specific. Call mark on 0403151598. Gear is at Berwick in south east outer Melbourne. I'm literally packing as I type this. Most of the gear will be getting packed and I'll be leaving Tuesday if it isnt sold. so don't wait around to call!

hey mate, how much you chasing for the dump and front pipe?

$1800 need em gone!

anyone interested????

sorry mate no pics. definately fill up the gaurds though.

Hi all, this is my first post, i have a set of Rays Engineering Volk Alloys for sale 8ïnch front and 9inch back. fantastic condition however the tyres are not the best due to them rubbing on the side of my gaurds. i have attached some photos, including sizes etc. chasing $2000 or closest offer. feel free to get in touch, usually on here browsing daily. item is located south eastern suburbs melbourne tom