Search the Community

Hi All, I bought a complete R32 RB26 to use the head on a 26/30 and am now looking to offload the bottom end. It has had something go through it so it will require new pistons and a bore to 86.5mm or possibly 87mm. I'm looking for: Block - $150 Crank - $150 Rods & Pistons - $80 Or: Crank, rods & pistons - $200 Crank, rods, pistons & block - $300 I also have: RB26 sump modified to suit RWD - $100 factory oil cooler/heat exchanger - $30 AAC Valve - $50 Standard fuel rail modified to be twin entry - $50 You can contact me via PM or on 0427 123 414 Cheers, Shane

Looking for pistons for rb26dett, preferably bore size 86.5mm, that can ship to UK.

RB25DET PARTS All that is in the picture, direct all question to my email address [email protected] with the words "skyline parts" in the subject line. http://i858.photobuc..._1/SAM_0384.jpg PRICE IS ONLY $120 ono. I live in bridgeman downs 4035 area. Maybe able to deliver, i work in indooroopilly. * top and bottom plenum * throttle body * sump * oil pump * water pump * exhaust heat sheld * crankshaft sproket in excellent condition * 5x pistons, in excellent condition. * oil strainer * intake and exhaust cam grears. * rear oil seal housing. Dont have any other parts available. Cheers for looking guys

hello! i have been looking for information on how to rebuild the brakes on a 1995 r33 gtr. i would like to rebuild them myself, but i am having a heck of a time finding anything other than replacement seals. i am looking for replacement/ upgraded pistons, torque specs, the gasket that goes between the caliper halves, if any. i have searched for any kind of documentation on this, but i don't seem to find anything other than engine manuals. on the bremboparts.com site, they only offer replacement pads. no pins, shims, or anything else. does anyone have, or know of, a walkthrough of how to rebuild the calipers? does anyone know of a place to order replacement parts? as these are brembos that were widely used, i really thought all this stuff would be more readily available.

i dunno wat its worth about 600$? bottom end, crank pistons rods etc. all still in block. Nothing was wrong with bottom end, I just built a new 30 so its not required any longer. dry and wet tests prooved 165ish across all 6. engine never missed a beat, and pfc knock always below 20! so its in good nick. Needs sump and oil pump. (stolen for new engine). block is plastic wrapped and ready for pickup. Price is neg. can get pix if required. 0419745910 - dale

Standard pistons or not??? Are these standard pistons? Any info would be appreciated thanx

Gday, Project engine has been scrapped so the pistons i bought are for sale. Brand new mahle forgies 0.020" over size (86.5mm for the metrics) Complete kit with rings and pins all brand new. Mahle are highly regarded as one of the best piston makers around. These pistons come from the factory friction coated on the skirts and heat coated on the crown. Also have a set of std rods that have been cleaned and re-sized bigends with ARP bolts fitted. The pistons and rods (with arp bolts) are proven for big power. Nice and cheap: pistons and rods for $1000 You wont find them cheaper. Im taking a hit on them because i need the money. Pick up: Hills District 0422 729 679 (LUKE)

Guys and Gals, I have for sale a set of 4 TE37s in 17 x 9.5" with a +12ish offset (not 100% sure). They have been resprayed in satin black (were originally bronze as the back side of the face has not been sprayed and you can see it), and they have nismo decals instead of the Rays Engineering and TE37 ones. All four rims have light rash and a few paint chips on the spokes, as whoever had them before me obviously couldnt drive to save their life, however in saying that, they could be easily repaired. No dents or buckles, they roll true. They come free with a set of shagged Toyo R888, as i used them as my track rims. Had them on my white R32 GTR and it looked tough as. Will no longer be needing them as doing a brake upgrade and they wont fit inside the rims anymore, so they gotta go. Price $2000 or best offer. Im on here daily so PM me with your mobile no. if genuinely interested and ill SMS some pics as i cant download them.

Farndon (more info below) full billet counterweight standard stroke crank (2.6L), apexi 86mm std bore pistons and Carrillo rods. This gear was installed in a motor built by JHH racing, but never ran before getting pulled down for a different setup. The crank is used and has been crack tested since last use, the Pistons and rods are both new. A JHH Inspection report is available which outlines the mint condition of this assembly. Make no mistake - if you want a high HP high revving 2.6 then this is some of the best gear available. I have a heap of other GTR parts for sale - please contact me on 0403221200 if you have any queries. $4500 for the full set The item is located in Gladstone QLD, but can be freighted any where in Australia. Please contact me for a freight quote. ****************************************************************************************************************************************************************************************** Farndon does machining for Apexi, BMW, Mercedes, Jaguar etc, is all made in Britian and is top quality (see below extract from their website). Apexi cranks were almost exclusively made by these guys. Extract from website: CRANKSHAFTS We offer a full design, development and manufacture service for crankshafts machined from solid steel billet, cast or forged material. All crankshafts manufactured are fully stress relieved and crack detected prior to shipping by Magnetic Particle Inspection (MPI) in accordance with BS6072. We also offer a full regrind service including MPI. Highly versatile manufacturing processes allow an infinite number of crankshafts configurations to be produced including: Cylinders 2, 4, 5,6,8,10,12 or 16 Plane Single/Multi Straight, Flat or Vee Max. Length 1,600 mm Materials To suit application Manufacture Billet Any type of Crankshaft, Heat Treated to Raise Core Strength Forged Farndon’s Own EN19 Lotus Twin Cam, Customer’s Own or Special Order Cast Customer’s Own or Special Order Finish Nitrided to Depth Required Balance Fully Balanced Ready For Installation Inspection Full Metrology Service Marking Engraved to Identify Origin Standard Features Custom Web Forms Including Wedging & Knife Edging, Heavy Metal Balancing, Splining, Gear Splining, Gear Cutting, Oilway Drilling (Pin to Main or Full Cross Drilled) See website for more info: http://www.farndon.com/crankshaft-manufacturer.html

These are 86mm standard bore size and are the special nickel / molybdenum coated versions. part number 2103-RN019 Pins and locks included. They are thick tapered wall HKS supplied pins New rings are readily available online or through HKS Australia Motor was running perfect when i pulled it down. Going to stroker so these are no longer needed. They are in near perfect condition bar one minor imperfection. Had them in bubble wrap in a box with my rods at the machine shop and for what ever reason one was taken out and put back in the box without bubble wrap as a result it had a bit of contact with one of my rods and a small imperfection and bur was left in the top ring land. I had that piston repaired and inspected at Special piston services and the receipt is in the photos. The ring sits in the groove perfectly and moves completely freely as it should. The effected area has no effect on the performance or strength of the piston this is me just being honest about the condition. There all perfect as can be seen from the photos. These normally are about 2-3k including freight and duties from japan $1000 ONO happy to post PM for details.

RB28 CP Pistons - $1,200 I have brand new (never out of the box) RB28 Pistons. These are to suit any RB26 stroker crank that uses standard rod length but alters the pin height of the piston (eg HKS, Spool, Nitto etc). Specs are: 86.5mm diameter 9.0 : 1 compression ratio 21mm wrist pin included Carillo rings included Perfect for 98 or E85 fuel and better off boost response than factory 8.7:1 CR. I'm only selling as I have decided to go higher CR due to running E85 only. Retail price is now ~$1,750 for these. Text me on 0438 036 375 Gav

FS NSW - CP Pistons 86.5mm to suit rb25 Hi all For sale, brand new set of CP pistons to suit RB25, 86.5mm bore. I picked these up by mistake with some other bits for my RB26 build, but they are the wrong make for me. This set is SC7308 as per pic, specific to RB25. Pistons only, no rods for sale. Some pins have been opened for inspection & trial fit only, never installed or run in an engine. Asking price $1000. Price is pretty firm, the cheapest I've personally seen these advertised for is $1320 brand new for the same set. Can meet / deliver around blacktown / 7 hills area most weekends, & potentially late on some weeknights. Local pick up only, not able to post around work. PM me on here or sms 0407 896 339 for any info. Cheers

i have a brand new set of pistons that i got with my brian crowed stroker kit, 25 or 26 2.9litre comp 9:1 these are custom made to suit the BC stroker kit so they won't work with your standard 26-25 crank after finding a crack in my block i ended up buying a n1 block so i ended up getting new 86.5 pistons so i get another bore cycle out of the block brand new, box only open for pictures inspections welcome sydney 2204 0404301881 $800

Rb26 head with greddy pro cams. ferrea 1mm os valves springs and retainers. Rear head drain/vent. Bronze guides. $2000 86mm cp pistons rb26 9-1 comp only used for assembly $450 Rb26 inlet manifold complete less injectors and rail $400

I've recently had to re-bore and tidy up my block due to a turbo failure. I ended up having to go up 20thou and buy new pistons to suit. These Tomei pistons are in excellent condition, having done approx 2500kms only. One has some marking on top from the piece of exhaust wheel that got sucked in, should clean up fine though. All else are spot on. These retail for around $1700. Looking for $750 posted.

For sale I have a forged rb26 short block i bought off a guy on SAU I paid $2500 do not want to sell for less, only selling because I've decided to go with a RB28 stroker kit Decked, bored, honed...Specs are as follows -Tomei oil restrictors -CP pistons -Eagle H beam rods -balanced r34 snub nosed crank -ARP bolts and bearings. Piston specs are 40thou oversized (87mm). Compression ratio is 8.5:1. The car ran 441awkw @ all fours on 24psi on e85 at Powertune Australia. Bloke I bought it off told me it had just been ran in and only reason he was selling was because he was going 3L bottom end. Great condition as seen in photos Inpsections welcome. $2500 easiest way to get me is on my mob:042188319

all parts came from a working motor 50 000 km selling because i built the motor happy to post, located parramatta for pick up rb26 pistons + rods rings etc - $100 ono bnr34 oem fuel pump - $50 ono rb26 harmonic balancer - $50 ono rb26 oem cam gears - $30 ono rb26 oem valve springs + retainers - $50 ono rb26 n1 mainstuds brand new - $20 ono rb26 water pump - $50 ono rb26 oil pump perfect working order good to put billet gears in - $70 ono rb26 head studs with washer - $20 rb26 engine mount - $40 ono bnr34 getrag mount - $40 ono rb26 heater hose kit autobahn 88 brand new sealed $100 200sx r33 adjustable caster rods - $50 r33 oem camber arms $20 apexi filter - 20$ s14 smic + all pipping - $50 s14 oem full exhaust system - $100 sr20 engine torque damper $20 2 x 200sx oem airbox's with filters - $70 each txt 0450 428 895 for photos etc

I have the following for sale: Brand new in box Tomei Forged pistons. To suit: RB26, or tomei 2.8 stroker. Size: 86.5mm Type:Same pin height as stock pistons non cooling channel valve reliefs in crown for high lift cams/v cam etc Includes: Pins, rings and circlips and a cool tomei sticker! Condition: new, never used, still in box Price: $1200 A pair of front DBA 4000 slotted discs for brembo front brakes Suit: Brembo 32-33-34GTRs Size: 324mm x 30mm Condition: Used, about 1 year old, no shudder Thickness of rotor: 29.71mm, wear limit is 28mm Price: $300 Location: West Brisbane QLD I can drop off around Brisbane. Postage cost extra and will be sent registered PM if interested Cheers

Hi everyone, I have the following up for sale as i no longer need it. As far as i am aware it only completed a few Dyno runs and not a cent was spared. The following is what was done: RB25 Motor Ross Racing Pistons Engine Gasket set incl. steek head gasket set Race Series Big End Bearings Race Series Main Bearings Welsh Plugs, big and small Serviced Cylinder Head Port and Polish Cylinder Head Machin block deck surface, balance crank and linish, balance pistons, balance rods, machined flywheel, removed aluminium plugs and replaced with steel plugs total cost when everything was done was over 6K (i have the reciept) $6,384.84 including labour etc Im chasing $2200 firm. Anyone who knows about building engines would see that the racing pistons costed 1300 so trying to get rid of it cheap. Any questions please ask. (as far as im aware it will need new oil squirters) thanks, Tom

Hey fellas. Got some stuff for sale. Polished cam/crank angle sensor. 4 months old. $400ono 20 thou over CP forged pistons, used good condition $500ono Eagle H-beam conrods, used good condition $500ono Pistons and rods still at machine shop. Can organise pictures if need. PM txt or call Gus 0423 534 006

Selling these pistons in good used condition, measure up like new. one piston has minor damage on top from previouse valve failure but has not affected the performance at all. selling due to stroker upgrade. SMS 0410419495 with any questions. pistons come with brand new Je gudgeon pins asking $350 ONO