Jump to content
SAU Community

Recommended Posts

Engine almost done nearly rdy to go thought id give you guys squiz see what ya reckons lol.

Ok list of internals

N1 Block

R33 crank grubbed & evrything else

Eagle rods

Mahle Pistons

Tomie Springs & buckets & retainers

Tomie 280s 10.8mm lift camshafts

Hypertune plenum 2 go on plus Trust manifold & greddy fuelrail

So far so good lol

post-23147-1197860175_thumb.jpg

post-23147-1197860499_thumb.jpg

post-23147-1197860566_thumb.jpg

post-23147-1197860650_thumb.jpg

post-23147-1197860697_thumb.jpg

post-23147-1197860749_thumb.jpg

post-23147-1197860800_thumb.jpg

post-23147-1197860849_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/197957-rb26/
Share on other sites

Hey man,

nice engine just wondering why you chose HKS (3 bolt) cam gears? a few guys in canada put a few posts up about these HKS cam gears becoming lose and have resulted in a couple of dead motors.... The said after this most people with new builds tend to go with 5 bolts type cams gears... not 100% sure of this, but food for thought.

Also what bearings did you use for you main bearings? N1 or Std H2O pump?

Arp bolts? stnd or After market oil pump?

cheers

Engine almost done nearly rdy to go thought id give you guys squiz see what ya reckons lol.

Ok list of internals

N1 Block

R33 crank grubbed & evrything else

Eagle rods

Mahle Pistons

Tomie Springs & buckets & retainers

Tomie 280s 10.8mm lift camshafts

Hypertune plenum 2 go on plus Trust manifold & greddy fuelrail

So far so good lol

Link to comment
https://www.sau.com.au/forums/topic/197957-rb26/#findComment-3538107
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...