Jump to content
SAU Community

L24e - Throttle Has No Effect

Daewoo

By Daewoo,
in Classic & Vintage (1950's-1980's)

 Share

Recommended Posts

Daewoo Enthusiast

Daewoo

Posted
Posted

I thought I would start a new thread for this, even tho I mentioned it in the previous thread I started... also helps me get my post count up :D ...

On a more technical note, one of the cars, that is destined to become the primary hack, had a blown head gasket. I had one of my heads overhauled (not sure what model, kidney shaped combustion chamber, small valves, FI ports (E88 rings a bell)... I ported it a little and matched it myself for free... I stripped off all of the polution gear and water heating for the manifolds/TB that I could see...

I now have two problems, I can get the car to start, it has fuel and spark, but nothing I do to the throttle has any effect... I changed the AFM and TPS with no effect... the car was running until the head came off, and I am a bit lost for ideas...

it is also pissing water out of either the head/block joint or Inlet Manifold/Head joint (where I don't think there are any water galleries). I am thinking perhaps one of the manifold studs/bolts has penetrated the water gallery in the head. I don't want to pull that apart until after I get the car running so I can transport it...

Any ideas???

The car starts and idles very badly (no exhaust, just headers)... but opening the TB has no effect, opening the AFM has no effect... the car just continues to idel exactly the same... I am wondering if one of the sensors I have disconnected would send the ECU into limp mode or something...

Cheers,

Daewoo

Link to comment
https://www.sau.com.au/forums/topic/302545-l24e-throttle-has-no-effect/
Share on other sites
noddle Rising Star

noddle

Posted
Posted

I assume this is a MR30, look at this,

http://noddle.customer.netspace.net.au/MR3...ediagpage5.jpeg

it may help diagnosed your problem.

here are some more wiring diagrams that may help you out

http://noddle.customer.netspace.net.au/MR30

Nigel

jrh001 Proficient

jrh001

Posted
Posted
....

The car starts and idles very badly (no exhaust, just headers)... but opening the TB has no effect, opening the AFM has no effect... the car just continues to idel exactly the same... I am wondering if one of the sensors I have disconnected would send the ECU into limp mode or something...

Just an uneducated guess here but there is a throttle valve switch that tells the ECU if the throttle is fully closed or open. Is that still connected?

JH

Daewoo Enthusiast

Daewoo

Posted
  • Author
Posted
Just an uneducated guess here but there is a throttle valve switch that tells the ECU if the throttle is fully closed or open. Is that still connected?

JH

That sounds like a likely culprit... where is the sensor for that located on the TB?

noddle Rising Star

noddle

Posted
Posted
Yep, that's what I was calling the throttle postion sensor... connected, and swapped it with one I know works without effect...

Cheers,

Darryl

This switch has to be aligned, ie

it's a two way switch,

position one, is no throttle

position two, full throttle (3/4/ I think it is)

there is no linier value with this TPS.

Nigel

Daewoo Enthusiast

Daewoo

Posted
  • Author
Posted
This switch has to be aligned, ie

it's a two way switch,

position one, is no throttle

position two, full throttle (3/4/ I think it is)

there is no linier value with this TPS.

Nigel

I dare you guys not to laugh when you read what the problem ended up being... I dare you...

The cars are at a mates place, and he has a lot of trouble with wasps making their mud nests in every available hole... so he had jammed a black spray paint can lid into the pipe from the AFM to the TB... right in the middle where the pipe bent... to stop wasps nesting in the inlet manifold :rofl:

so the car now runs (very badly but runs)...

Next problem tho... this car was supposed to be fine other than a blown headgasket... so I have now changed the head gasket and oil and filter, and the oil is again just as white as before I started... head is torqued correctly, so I don't think it will be a gasket (didn't really check that the block was flat I guess)... anywhere else where wet stuff often mixes with black stuff to become white stuff???

Cheers,

Daewoo

noddle Rising Star

noddle

Posted
Posted
I dare you guys not to laugh when you read what the problem ended up being... I dare you...

The cars are at a mates place, and he has a lot of trouble with wasps making their mud nests in every available hole... so he had jammed a black spray paint can lid into the pipe from the AFM to the TB... right in the middle where the pipe bent... to stop wasps nesting in the inlet manifold :)

so the car now runs (very badly but runs)...

Next problem tho... this car was supposed to be fine other than a blown headgasket... so I have now changed the head gasket and oil and filter, and the oil is again just as white as before I started... head is torqued correctly, so I don't think it will be a gasket (didn't really check that the block was flat I guess)... anywhere else where wet stuff often mixes with black stuff to become white stuff???

Cheers,

Daewoo

I've seen holes in the front timing cover once, it had corroded through, into the engine

coupe72001 Mentor

coupe72001

Posted
Posted

Agreed. I redid my head twice before I realised the problem was a actually pin hole in the timing cover - not noticable until I held it up in the sun and saw the light, so to speak. From memory there is also a hidden welsh plug under the timing cover, so that may also have corroded.

wardie Enthusiast

wardie

Posted
Posted
Thanks for that info...

Yeah, you can drop the timing cover if you drop the sump, done it a few times on the 1600...

I'll check that out...

Cheers,

Darryl

I've had the hole in the back of the water pump twice now. Got it welded the first time and replaced it with one from an L20 the second time.

Daewoo Enthusiast

Daewoo

Posted
  • Author
Posted
I've had the hole in the back of the water pump twice now. Got it welded the first time and replaced it with one from an L20 the second time.

This will be the first thing I check when I go to work on the car this weekend...

Cheers,

Daewoo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      First time we have seen lights 
    • Wazmond
      WGNC34 - floor mats

      By Wazmond · Posted

      I think Fitmit had some, have a look on there (theyre Australian as well)
    • soviet_merlin
      Howdy Y'all

      By soviet_merlin · Posted

      Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...