Jump to content
SAU Community

R34 (Neo Straight 6) Power FC Question


Bass Junky
 Share

Recommended Posts

Hey Ppls,

Previously I thought the extra throttle body type device was a traction control thing which shut when wheelspin was evident.

I have since been told that this is actually a Variable Intake Flow thingo which acts to increase airflow speed at low rpm by closing like a normal throttle body, and then opening up at high rpm to give bulk airflow.

Now, PowerFCs are suppose to control all features of the engine management, and I would assume that this is a very important part of the Neo 6 engine.

To those who know, does the R-34 PowerFC allow you to control the activity of this throttle body device........??

I would assume that you could adjust this similar to the way you can with the NVCS.

Having said that though, it might have a link to TPS in order to give the best results depending on a lot of other variables......

Anybody with any experience??

Cheers

BASS OUT

Link to comment
Share on other sites

Are you talking about the bit that sits across the inside of the plenum? it's open at low revs, then closes at high revs...speeds up the flow of air at high RPM. If you disconnect it you'll notice the car runs like a dog from about 3200-5000ish,then picks up in the last bit of the range.

Link to comment
Share on other sites

Yep, that's the bit.

Any definent answers??

when I disconnected the plug to it last night, the Engine Warning light came and on the Slip/TCS off light lit up and I took it for a drive.

I didn't really notice a lot of difference but the car was cold and I couldn't really give it a good thrashing.

Link to comment
Share on other sites

Guest RedLineGTR

The thing that is in front of the throttle body, is for the Traction Control System :D its what limits your revs when u are wheels spinning from the line, hence if you try to launch with the TCS on then you bog down quite bad. Hope it answers you question.

Link to comment
Share on other sites

Guest RedLineGTR

The Power Fc will control everything the same as in other skylines (in one way or another) the Neo engine is tuned for more power (more R&D) over the past models. The TCS Has a Seperate ECU for what it does and u cant change any items of how it behaves with the power fc nor do i know any companys that have Tuned it in one way or another.

Link to comment
Share on other sites

Guest RedLineGTR

I hope this is what u mean by your question. When the TCS is activated it is activated and if the car starts to slip highly then it kicks in just like i throttle body, like if you are on the pedal to the floor the TCS can ajust its throttle and limit your revs. If the system is off then the air flows how its meant to without any interuption.

Link to comment
Share on other sites

My experience with the traction control is as follows.

Going around slight corners and nailing it, the car will pull lose power and then accelerate once grip is gained again.

But in the wet the car will drop spark and the engine will 'strobe' (for want of a better word) for a second and then accelerate, at which point traction will be lost again, and then it will strobe again.

I think maybe in moderate losses of traction, the blade might close, butin big ones it drops sparky and really pulles the reigns in.

If it only works for traction control, I wonder it there is any merit in using it as a variable intake diameter type device????

Link to comment
Share on other sites

What makes you think it "drops sparky"? It just closes the valve completely starving the engine of air and probably cuts the fuel at the same time. If you cut spark it would backfire when you gave it back.

At it's most basic it just cuts power so you can get traction back and if you keep your foot down then it will spin the wheels again, thus restarting the whole process.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • There's probably an underlying issue with the A/C system too. I recently fixed mine, now it's fully control by the Haltech and car's factory HVAC controller  Have a squiz here:    
    • And by the way, I've also checked the ECU diagnostic numerous times and got a bad O2 sensor code and initially an Ignition Primary code, which is why I replaced the O2 sensor and all the ignition components (coil packa, plug and loom). No codes have been coming up lately despite the ongoing issue.
    • Hey pber13, unfortunately still no luck. At this point the following has been done with little or no success: - Spark plugs replaced, gapped to 0.8mm - Splitfire coilpacks installed to replace originals - Replaced Ignition Coil/Coilpack harness with a new genuine nissan one - New fuel filter - Replaced AFM/MAF sensor - Injectors have been thoroughly cleaned with an online flush (without removing) - Upper engine and inlet decarbed - blew tons of black smoke out, cleared the carbon deposits from the top of the engine and exhaust.  - IACV removed and thoroughly cleaned with carburettor cleaner - O2 sensor replaced with new and genuine one -  Smoke test revealed no vacuum leaks - Healthy compression test of 160psi across all 6 cylinders Overall the car does run a lot smoother now, no backfires between gear shifts like it did originally... but the rough idle when warmed up is still there. It may not even be a misfire but simply a rough idle. Seems crazy to me that so many people have had this issue and seemingly no one has gotten to the bottom of it, or at least never bothered to post if they did! Hope you have more luck than I did pber13, I'm at a point now where I'm just going to try to ignore it unless it gets worse. Would love to fix it but I've genuinely run out of ideas of what it could be.
    • I got the full frenchys kit too. Really awesome kit. Easy to install my only complaint was the hardlines I think could be routed differently (I modified mine) but I realise the kit needs to suit multiple applications. This was the hard lines before I modified them. They were touching the wastegate pipe. I ended up reducing the distance between firewall and first bend. The made it so they tucked along the frame rail.
    • Deeve, I don't suppose that you've made any progress on this? My Stagea has the exact same problem, and just like you, I've read through as much as I can online, with no real progress. My car isn't throwing any codes at all, which is a little frustrating. I've changed plugs, checked the wiring and harness. A new MAF gets here next week, but I'm not hopeful it will solve the issue.
×
×
  • Create New...