Jump to content
SAU Community

Fs: R32/rb20Det Parts

XkyleX
 Share

Recommended Posts

XkyleX Contributor

XkyleX

Posted
Posted (edited)

Just recently did a turbo swap on my RB20, got a few parts to get rid of......

Great condition RB20DET turbo:

It is a 1993 model, great condition, very minimal shaft play, wheels are in great condition, housings are equally good, was a great turbo, never blew and smoke. would be great for someone wishing to replace a blow unit, or as a spare, or even if you were looking for one to hi-flow...

Price - $100

IMG_0648.jpg

JJR Split dump:

Great condition, no damage to the flanges, thread for o2 sensor still in perfect condition....

Price - $50, they retail at $95 from Just jap

IMG_0642.jpg

R32 Supermade Boot spoiler

Only recently picked this up, but have decided to keep mine wingless.....it is in great condition, is stupidly light, would be simple to colour match if you needed too....

Price - $150 Not neg (this is what i paid, just trying to get my money back

IMG_0650.jpg

pic below, the spoiler is not centred...

IMG_0254.jpg

Contact via PM or 0401 373 060

Located in Campbelltown NSW

Edited by XkyleX
Link to comment
Share on other sites
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • robbo_rb180
      R32 Gts+t Daily/street

      By robbo_rb180 · Posted

      Nice work on the shroud/ducting.  
    • ELFGT350
      Newbies

      By ELFGT350 · Posted

      Hi and best of luck with your car. Its a bit hard to tell how low the car is all round from that pic or if its been lowered or not. 90mm is a bit low on the front apron but it depends on the shocks & springs condition & whether or not its been lowered. Going to 19” wheels will give you 15-20mm depending on rubber but you might need new shocks. Mine -2005 are weeping fluid slightly but have lasted 19years!!. So if yours are original they need replacing anyway if they havent been touched before.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Hi everyone, Recently got handed down a 2004 Skyline 350GT Coupe. I would like to change the wheels as the previous owner installed some weird ones. The current ones are 215/45ZR18, unsure of the offset, and sit pretty deep in. Would like to increase the ground clearance slightly as well as I need to get it roadworthy standard, currently sitting at 90mm. Was thinking that maybe I could kill 2 birds with 1 stone by getting new wheels.  Pictures of current wheels: https://imgur.com/bg1QMIu Any recommendations for the types of wheels I should be on the lookout for? Like the maximum and minimum offset, sidewall height, width, etc.  Sorry in advance if I'm noob, I do not know much about cars other than how to change the oil, a blown tyre and brakepads....
    • Lvonn1
      RB25DE Rebuild tolerances

      By Lvonn1 · Posted

      Hey MinKer, Where abouts did you get that table from ? 
    • joshuaho96
      Problem with 5th after manual swap on R32 GTS4

      By joshuaho96 · Posted

      Most likely your engine is toast, but also the R32 GTR has different ratios than the GTS4. In 5th it's basically the same, it's mostly 1st through 3rd that change. Stop trying to do WOT pulls before you make the engine entirely unsalvageable. Do a leakdown test and/or borescope the cylinders first. And a boost leak can overspeed a turbo. Make sure the turbo actually functions as intended.
×
×
  • Create New...