Jump to content
SAU Community

R34 Gtr - Fan Shroud

GTR600

By GTR600,
in Cosmetic, Styling & Respray

 Share

Recommended Posts

GTR600 Proficient

GTR600

Posted
Posted

Hi,

Can anyone point me in the right direction for a radiator fan shroud that sits ontop of an aftermarket radiator like the picture attached. The OEM shouds do not work as they are bolted to the standard radiators - ofcourse aftermarket radiators do not have these bolt locations - well atleast my ARC radiator does not.

See pic attached

post-77232-0-74654700-1305040396_thumb.jpg

Link to comment
Share on other sites
GTRsean Grand Master

GTRsean

Posted
Posted

Nice car :cool:

I know that some aftermarket radiators do have the mounts for the stock shroud, such as cooling pro.

You could get some mounts welded on and drilled?

Link to comment
Share on other sites
GTR600 Proficient

GTR600

Posted
  • Author
Posted

Thanks - thats not my car - pic I found with the shroud im looking for.

Good idea, did think of that, might have to explore a little further. Anyone have a Shroud they would like to sell?

Thanks again Sean

Link to comment
Share on other sites
GTRsean Grand Master

GTRsean

Posted
Posted

Here's an updated pic for you....has the catch can fitted in this pic, pic is my car.

Shroud is pretty important, so good luck with your search. Just put up a topic in 'wanted to buy'.

post-12712-0-07165500-1305115268_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • portaz
      Walbro 460 in r32 gtr

      By portaz · Posted

      I disconnected before the fuel pump and restriction still there. Disconnected at turbosmart fpr and also after ethanol sensor and pressure dropped. No kinks in line but I found one spot above diff that I can hear the fuel flowing while running so I'm wondering if there is built up corrosion  from 10 years of sitting.  I had injectors cleaned and tested and one was dead but rest were fine. Was never an issue when I owned the car previously but I'll talk to jez about his thoughts on if they should be changed to newer tech. Thx guys at least I know the setup should work again. Pump is wired directly to relay and not using factory plug any  more 
    • robbo_rb180
      R32 Gts+t Daily/street

      By robbo_rb180 · Posted

      Nice work on the shroud/ducting.  
    • ELFGT350
      Newbies

      By ELFGT350 · Posted

      Hi and best of luck with your car. Its a bit hard to tell how low the car is all round from that pic or if its been lowered or not. 90mm is a bit low on the front apron but it depends on the shocks & springs condition & whether or not its been lowered. Going to 19” wheels will give you 15-20mm depending on rubber but you might need new shocks. Mine -2005 are weeping fluid slightly but have lasted 19years!!. So if yours are original they need replacing anyway if they havent been touched before.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Hi everyone, Recently got handed down a 2004 Skyline 350GT Coupe. I would like to change the wheels as the previous owner installed some weird ones. The current ones are 215/45ZR18, unsure of the offset, and sit pretty deep in. Would like to increase the ground clearance slightly as well as I need to get it roadworthy standard, currently sitting at 90mm. Was thinking that maybe I could kill 2 birds with 1 stone by getting new wheels.  Pictures of current wheels: https://imgur.com/bg1QMIu Any recommendations for the types of wheels I should be on the lookout for? Like the maximum and minimum offset, sidewall height, width, etc.  Sorry in advance if I'm noob, I do not know much about cars other than how to change the oil, a blown tyre and brakepads....
    • Lvonn1
      RB25DE Rebuild tolerances

      By Lvonn1 · Posted

      Hey MinKer, Where abouts did you get that table from ? 
×
×
  • Create New...