Jump to content
SAU Community

K Sport Coil Overs

jays r33 gtr
 Share

Recommended Posts

jays r33 gtr Community Regular

jays r33 gtr

Posted
Posted

Hey guys as stated im having problems lowing the lower perch on my k sport coil overs?

it seems as though it has like seized up and i can not adjust the height.

Has anyone experienced this with theses coil overs and what did you do to loosen them up?

thanks jason

Link to comment
Share on other sites
RS4-S Proficient

RS4-S

Posted
Posted (edited)

i havent seen it with k-sport but i have on some BC's on a vrx lancer. all we did was flush the lower mount with Rost off (WD40) to try and get some of the dust etc out of the threaded section and lubricate it abit. it did free up but was still very stiff. if your adjusting the height wouldnt you be adjusting the lower section of the coilover and not the spring purch? cos then you are just adding moreor less pre load on the spring

Edited by RS4-S
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Rear suspension upgrades

      By Duncan · Posted

      swaybar swaybar swaybar swaybar swaybar anyway OP, what is currently in your car, are they factory shocks and sway bar? Any sign anything else has been changed under there over the years? And as Murray said....what are effect you looking to change
    • Duncan
      Manual Shifter slightly bounces/moves/vibrates when accelerating/deaccelerating

      By Duncan · Posted

      Congratulations on your find  Did you mean it has 6k miles or was that a typo? Firstly, keep in mind some movement of the shifter is normal...it is a long rod hanging out of a box bolted to the engine. Having said that there are 2 next places to look: 1. Transmission and engine mounts. If these are worn or broken the shifter will move around more. They are reasonably easy to source and replace on a hoist, and possible but uncomfortable to replace car stands 2. On the bottom of the shifter there is a nylon cup that sits over shifter's ball end. If this is worn or broken the shifter will move around more than it should (but will still shift OK). That is a cheap part and requires removal of centre console, rubber shifter hole covers and a circlip in the gearbox shifter hole to remove the shifter. Re maintenance, as with any new import you should change all the fluids including transmission when you get it; never trust the seller and previous owners to have done the right thing. I am pretty sure R34 GTT is the same as earlier big box transmissions, so use any good quality GL4 75w90 trans fluid if it is shifting well (if it is hard to shift due to synchro wear, redline shockproof lightweight will keep it alive a bit longer before rebuild is required)
    • Chris_Guthrie
      Misfire/stalling issues

      By Chris_Guthrie · Posted

      Well considering I have the exact same problem with that as the original one I don't think that the ignitor is the problem. I would imagine that this being such an uncommon problem the possibility of getting a new ignitor that is bad in the same way as the old one has to be very slim. I'll definitely pull everything apart this weekend and check the turbo out. Got quite a bit of things to check out Saturday like fuel pressure and the pcv so I'll report back once I do that.  Thanks everyone for all the replies this is all really helpful  
    • dodo1410
      Rb26 expected power

      By dodo1410 · Posted

      It’s 98
    • TurboTapin
      Rb26 expected power

      By TurboTapin · Posted

      Rb's have issues with bottom end starvation, not head starvation. Which either way, you probably wouldn't ever see on a dyno. Strange... What's pump gas for you? Octane rating?
×
×
  • Create New...