Jump to content
SAU Community

Recommended Posts

Hi guys,

since we last spoke about the car, I ended up opting for a rebuild.

Got 'ruby' to do a full rebuild; rings, pistons,conrod bearings, and a few others bits. car has been run in done over 1200kms in her.

But still have a few persistant issues, I would LOVE some honest advice, if anyone has experienced this before?

first of all, on first start in the morning, I will kick the car over, it will idle quite low roughly 500rpm for 5secs and then DIE, unless I give it a touch of throttle, it happens every time I start it for the day - could be cold start. or timing??

Secondly - I am running an r32 actuator on constant 10Psi; I am being told it could be a R&R issue, the situation is at times when cruising or accelerating the rpm will flow upwards while I am accelerating, BUT at times it will feel like the rpm is backing off, or the throttle is backing off when my foot is on the pedal, I am trying to increase throttle but it will back off for a second; this can be on a normal throttle or even on big throttle increase.... and lately the car has been making a HUGE induction sound, like a turbo BUT much louder can be heard from inside the cabin (like a whistle or woooosh)

THE CAR is 1993 R33 S1 - stock turbo, engine, ecu, only mods are FMIC, 3inch turbo bk exhaust & cat, and that R32 actuator...... I have been told a few different answers; it may be running R&R (but why?) it could be the AFM? or TPS (timing)

I have booked in for a DYNO run and for the guy to check AFR levels and see what comp says...... It seems like a never ending issue, and I have no idea where to begin....

AS said everything is basically STOCK - it boosts good around 3-4k not sure exactly, but gets to one point at the top of the RPM and spools up, boosts but then kinda sounds like a backfire, as there is NO BOV! it sounds different??

ANY ASSISTANCE APPRECIATED - AM HOPING THIS NEW GUY WILL FIND THE ISSUE AT THE DYNO!

cheers guys, this is my first import and it means alot to me, just abit frustrating lately

Link to comment
https://www.sau.com.au/forums/topic/390420-major-persistant-issue-on-r33/
Share on other sites

U should wait until the guy with the dyno has looked at it before you go out and start throwing parts at it.

Don't listen to nonsense about R+R, it's the inexperienced mans way of diagnosing every miss fire or hesitation. Your problem sounds like its timing related due to the description you gave about the induction sound etc so AFM would be the most likely starting point but it all depends on how good your description is. Quite possibly a fuel pump also

What rpm does this all happen at, is it everywhere? Or is it at the typical peak torque point on full throttle of 4500-5500 or is it both.

If it is just the peak torque point then yeah, Id say R&R due to plugs, coils, too rich etc. But if it is happening elsewhere then I believe you have other issues.

What rpm does this all happen at, is it everywhere? Or is it at the typical peak torque point on full throttle of 4500-5500 or is it both.

If it is just the peak torque point then yeah, Id say R&R due to plugs, coils, too rich etc. But if it is happening elsewhere then I believe you have other issues.

the rpm/throttle backing off - well its hard to explain, as I said i would be accelerating as normal to drive or overtake and at certain point usually over or around 4k give or take. and then it would feel like the car is literally backing off accel on its own for a second..till i press throttle a lil, almost like a flat spot or a miss (im a total newbie with skylines :P )

plugs were just checked and gapped by a good friend. and yes I will wait for DYNO, but I like to know others personal experiences (just hope the guy knows his stuff, because previous shop didnt assist or I didnt explain it right?)

Its all a learning curve guys, so bare with me here :D

My car fails to start first time, most of the time when cold. Read about it skyline starting then stalling on first start, its very very common yet there is no uniform fix. Some say water temp sensor, some say cas, some say tune, some say leaky injectors. I honestly have no idea but I don't care anymore, i'm used to it. I've also got an r33, when you do your reading you will see its mostly r33's that do it.

the rpm/throttle backing off - well its hard to explain, as I said i would be accelerating as normal to drive or overtake and at certain point usually over or around 4k give or take. and then it would feel like the car is literally backing off accel on its own for a second..till i press throttle a lil, almost like a flat spot or a miss (im a total newbie with skylines :P )

plugs were just checked and gapped by a good friend. and yes I will wait for DYNO, but I like to know others personal experiences (just hope the guy knows his stuff, because previous shop didnt assist or I didnt explain it right?)

Its all a learning curve guys, so bare with me here :D

So you have described it is down on power at peak torque, does it misfire (a misfire sounds like a pop, pop, pop) or does it just splutter and feel like it has just stalled?

Does it ONLY happen at 4-5k or does it continue to happen from 4k to redline?

Does it also happen at idle/low revs/low load?

To answer your question of why do I say R&R or why fuel pump or even why cas/afm this is why:

If it happens from 4k to redline and is more of a splutter just no power I am going to say it is your fuel pump that is dying as a dying fuel pump generally provides fairly consistently not enough fuel at all times, this means when > x fuel is needed the car leans out and basically dies in the ass, eg > 4k rpm and it just doesn't have enough fuel to run. This generally won't be a pop, pop, pop but just the car feeling like it is dying and you've taken your foot off the accelerator.

If it ONLY splutters at 4-5k (peak torque) this is when the maximum fuel and air is in the cylinder, this is when the mixture is the hardest to ignite and also the point the ECU makes the fuel as rich as possible. Hence bad plugs/coils (weak spark) and lots of fuel (needs strong spark to ignite) means if the car is going to misfire due to a spark failing to ignite the mixture, it will do so here. Hence why people often find the car misfires (loud pop, pop, pop) at 4-5k but then find the car revs out cleanly to 7.5k. This is usually caused by a combination of bad spark (cracked/cooked coilpacks or old sparkplugs) and overly rich fuel mixture eg 10:1 AFR due to the ECU going to the rich and retarded quadrant of the load map, lowering the boost to stock or retuning this part of the map will fix this issue.

If it seems to happen randomly everywhere and is just generally shit it may be something like a failing sensor eg AFM or CAS as these are usually intermittant and don't get worse dependant on load, they just randomly shit themselves for no reason. Hence stalling, missing at odd revs, down on power and generally all round shit performance. However fuel pumps can also fail intermittently and cause it to stall at idle, and cause the lean out situation randomly.

These are just all general diagnoses, it could be any all or none of the above, and they could all exhibit completely different effects, though generally they will do as I have described.

Note this is important, if it is the fuel pump leaning the car out causing it to die then this is a DANGEROUS situation as it can cause the engine to ping/detonate due to running lean, this will melt pistons and generally destroy your engine very fast so don't go driving it around trying to rev it out over and over again as you may do permanent damage to it.

Once on the dyno it will be very easy to see if it is failing fuel pump, get it there asap. Plugging a consult cable in will sometimes diagnose failing sensors, though unless they completely die the ECU is often unaware that they are giving inaccurate signals.

edit: I can't believe I actually bothered to type all that out, must be in a good mood.

Edited by Rolls

THANKYOU - I will try to answer to my best ability, but remember my knowledge and mechanical vocabulary is limited :P

Okay - there is no pop that i can tell, if i take foot off accel it makes a gurgle kinda sound but even my SS did that... its not really a splutter or stall - think of this - accelerating from 0 and rpm going up to say 100km/hr or more... as you are climbing in rpm it will feel like it backs off for a second, not a fluid motion up the rpm, its only for say 1-2secs where it will back off slightly, could be described as a lil flat spot or blockage for a second, usually if i try to accelerate and it does it, I would take foot off and re-apply the throttle to make it move, this is mid cruise as i said generally around 3.5-4.5k rpm and its only for that instance not continual...( JUST like it wont go up the rpm kinda stuck for a second...?) - only remember it happening at the higher rpm range! (AS STATED - it doesnt die, just has a flat spot for a few secs when it should be climbing in RPM it stops for a second but no sound just the feel is wrong and the speedo & rpm gauge drops back a lil...?? if that makes sense!

** CAR HAS ONLY DONE 1200KM SINCE REBUILD, REPLACED ALL RINGS,PISTONS AND CONRODS ***

ALSO - lately I have been getting that super loud induction/suction sound that is very loud like a screamer but It doesnt have one nor BOV....

idle is fine - except the cold start (and yes I have read numerous forums on SAU and it is common)

DYNO - Booked in for MONDAY :)) hopefully good news if they pinpoint the issue, but also bad news because more $$$$

thanks again for the advice!!

So you have described it is down on power at peak torque, does it misfire (a misfire sounds like a pop, pop, pop) or does it just splutter and feel like it has just stalled?

Does it ONLY happen at 4-5k or does it continue to happen from 4k to redline?

Does it also happen at idle/low revs/low load?

To answer your question of why do I say R&R or why fuel pump or even why cas/afm this is why:

If it happens from 4k to redline and is more of a splutter just no power I am going to say it is your fuel pump that is dying as a dying fuel pump generally provides fairly consistently not enough fuel at all times, this means when > x fuel is needed the car leans out and basically dies in the ass, eg > 4k rpm and it just doesn't have enough fuel to run. This generally won't be a pop, pop, pop but just the car feeling like it is dying and you've taken your foot off the accelerator.

If it ONLY splutters at 4-5k (peak torque) this is when the maximum fuel and air is in the cylinder, this is when the mixture is the hardest to ignite and also the point the ECU makes the fuel as rich as possible. Hence bad plugs/coils (weak spark) and lots of fuel (needs strong spark to ignite) means if the car is going to misfire due to a spark failing to ignite the mixture, it will do so here. Hence why people often find the car misfires (loud pop, pop, pop) at 4-5k but then find the car revs out cleanly to 7.5k. This is usually caused by a combination of bad spark (cracked/cooked coilpacks or old sparkplugs) and overly rich fuel mixture eg 10:1 AFR due to the ECU going to the rich and retarded quadrant of the load map, lowering the boost to stock or retuning this part of the map will fix this issue.

If it seems to happen randomly everywhere and is just generally shit it may be something like a failing sensor eg AFM or CAS as these are usually intermittant and don't get worse dependant on load, they just randomly shit themselves for no reason. Hence stalling, missing at odd revs, down on power and generally all round shit performance. However fuel pumps can also fail intermittently and cause it to stall at idle, and cause the lean out situation randomly.

These are just all general diagnoses, it could be any all or none of the above, and they could all exhibit completely different effects, though generally they will do as I have described.

Note this is important, if it is the fuel pump leaning the car out causing it to die then this is a DANGEROUS situation as it can cause the engine to ping/detonate due to running lean, this will melt pistons and generally destroy your engine very fast so don't go driving it around trying to rev it out over and over again as you may do permanent damage to it.

Once on the dyno it will be very easy to see if it is failing fuel pump, get it there asap. Plugging a consult cable in will sometimes diagnose failing sensors, though unless they completely die the ECU is often unaware that they are giving inaccurate signals.

edit: I can't believe I actually bothered to type all that out, must be in a good mood.

Edited by mikeyR33-T

If your fuel pump is failing, you will get pops, like the car is shitting out self, believe me I know. You can very easily tell the difference between a failing fuel pump and lean pop. If you are losing power without any change from the exhaust sound, ie it still sounds like the engine running smooth, the problem is somewhere else and I would doubt the afm. A failing afm should cause shit idle too.

The woosh sound you hear is interesting too, it could be the cause of all your problems. Have you properly checked and made 1100% sure that you don't have a loose or slipped pipe in your intercooler line anywhere, or anywhere in your intake side? I popped off a cooler pipe, instant slug, loss of power etc but some how managed to idle okish.

try to fix it first without spending money. Start easy, do the stuff you can do and you should be able to fix or pin point the problem to have it fixed. You pay someone to find your problem, you pay big..

You might have an exhaust leak, either head > manifold, manifold > turbo, turbo > dump...

Edited by SargeRX8

If your fuel pump is failing, you will get pops, like the car is shitting out self, believe me I know. You can very easily tell the difference between a failing fuel pump and lean pop. If you are losing power without any change from the exhaust sound, ie it still sounds like the engine running smooth, the problem is somewhere else and I would doubt the afm. A failing afm should cause shit idle too.

The woosh sound you hear is interesting too, it could be the cause of all your problems. Have you properly checked and made 1100% sure that you don't have a loose or slipped pipe in your intercooler line anywhere, or anywhere in your intake side? I popped off a cooler pipe, instant slug, loss of power etc but some how managed to idle okish.

try to fix it first without spending money. Start easy, do the stuff you can do and you should be able to fix or pin point the problem to have it fixed. You pay someone to find your problem, you pay big..

You might have an exhaust leak, either head > manifold, manifold > turbo, turbo > dump...

thanks - but I dont know anyone with a dyno or computer program to test it, and I have no idea where to look for these parts in the engine, mechanical i have a mate but not computer related!!

You don't need a dyno. To diagnose for exhaust leaks, look for black shit building up anywhere where there are joints in the exhaust system. Another way is a piece of hose in your ear and run it around different joints in the engine bay, if you find an exhaust leak it will sound like a hiss on idle, or louder if its a big leak. Testing the fuel pump; Is the car hard to start? Does it lean pop when on power? The car will kind of turn into a machine gun when you are on boost. If you hear this you either are misfiring or having a lean condition. Either coil packs or fuel pump. Testing for intake leaks can be done two ways, you actually test the intake by charging it with air and sealing it off, or the other way you look for leaks, holes, cracks or anything which looks out of place.

You don't need a dyno to find anything. I have found almost every single car issue I have ever had right in my back yard, and I am a computer science graduate. All the stuff Ive mention isn't skyline specific, its general mechanic stuff.

You don't need a dyno. To diagnose for exhaust leaks, look for black shit building up anywhere where there are joints in the exhaust system. Another way is a piece of hose in your ear and run it around different joints in the engine bay, if you find an exhaust leak it will sound like a hiss on idle, or louder if its a big leak. Testing the fuel pump; Is the car hard to start? Does it lean pop when on power? The car will kind of turn into a machine gun when you are on boost. If you hear this you either are misfiring or having a lean condition. Either coil packs or fuel pump. Testing for intake leaks can be done two ways, you actually test the intake by charging it with air and sealing it off, or the other way you look for leaks, holes, cracks or anything which looks out of place.

You don't need a dyno to find anything. I have found almost every single car issue I have ever had right in my back yard, and I am a computer science graduate. All the stuff Ive mention isn't skyline specific, its general mechanic stuff.

I understand what you're saying, but my mechanical knowledge is limited at changing a tyre; checking oil, NO idea on the rest, So i have no choice but to get it dynoed which i wanted anyways

No hiss, no noise on idle itself..unless i de-cellerate then it kinda gurgles! cold start is bad in mornings first thing for the day to start it will idle very low maybe 300rpm for 5secs then die if I DONT give it a bit of throttle..

again no pop when boosting, except right at the end of the boost at high rpm like 6k when i back off after overtaking it will be at the end of the boost and kinda pop once unless thats the noise it makes with no BOV... but thats the only time!

I do recall NOW, that when car is turned on ANYONE can hear clicking noise coming from the dash area for a good 5secs when car is turned to power even before cranking??

I will get dyno for now! I dont trust myself to try to do anything, I have never serviced a car before!

Sounds like you better take it to a performance shop as it doesn't sound like you can do any work yourself bar change a tyre... so if you can't do it yourself then they are going to have to do it anyway. Might as well get them to figure it out.

If your fuel pump is failing, you will get pops, like the car is shitting out self, believe me I know. You can very easily tell the difference between a failing fuel pump and lean pop. If you are losing power without any change from the exhaust sound, ie it still sounds like the engine running smooth, the problem is somewhere else and I would doubt the afm. A failing afm should cause shit idle too.

A failing fuel pump will cause a lean condition though???

Sounds like you better take it to a performance shop as it doesn't sound like you can do any work yourself bar change a tyre... so if you can't do it yourself then they are going to have to do it anyway. Might as well get them to figure it out.

A failing fuel pump will cause a lean condition though??? (I have NO IDEA )

Rolls - I have it booked in mate, just wanted some advice if someone had a definitive answer, I have a good friend who could do mechanical side of things if some1 was to say YES it is AFM for sure.... otherwise a DYNO is the best idea at this point and hopefully it will show if its too lean or too rich or not enough air/fuel.

HOPE they know what they're doing, some places are slack

:P trueee, well I wanted a dyno anyway to see how the car is after the rebuild, so hopefully it tells me whats happening and if its R&R etc

cheers mate.

p.s will post back Monday night after the dyno

Yeah stuff like this is almost impossible to be 100%, even with the car in front of you you can end up swapping a few things before you figure it out. Welcome to the joys of cars, I hope you have lots of money.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...