Jump to content
SAU Community

Nissan Stagea C34 Black Series 2 - Urgent Sale


Recommended Posts

hey guys,

ive decided to sell my RS4 1998 series 2 Nissan Stagea. Im after swaps for a s15 or vy/vz ss commodore.

The car runs beautifully i have all the service history log book done by Gawler mechanic and from the previous owner at Jarret nissan.

1998 series 2 Nissan Stagea auto tiptronic AWD, Twin sunroofs. RB25DET

111,xxx kms, just had its 110,000 km service and at 100,000km had the water pump and belts replaced in its major service (have all reciepts)

- black, Just had a full stage 2 cut and polish paint protection and headlight restoration (done by hamish) excellent job not a swirl in it

- Silver 17 inch Drift Teks 17 x 8 all round with all tyres 80 percent tread

- WAG adjustable Coilovers

- r34 gtt front brakes

- new rotors and bendix pads

- N/A chrome Grille (just purchased from Mike)

- Clear nismo side indicators

- nismo radiator cap

- HKS turbo back exhaust

- Pod filter

- 1500 dollar sound system

pioneer headunit

front and rear JL AUDIO speakers

JL Audio 4 channel amp

- have all original stagea floor mats

- i have the sunroof visor that goes over the front sunroof to deflect the wind

- also have leather luggage pull over cover and mesh luggage thingy which stops stuff flying through from the boot.

contact Josh - 0418768819 dont pm i dont get much of a chance to get on here. i will mms pictures

Price 12,500 ono or swaps for a s15

located in S.A northern suburbs 9UIyP.jpg

ibE1h.jpg

hBVs6.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Euros are shitboxes man. My next car going to be a Lexus or Hyundai.
    • Maybe I used the wrong sandwich plate as well. Used one piece instead of two piece.  
    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
×
×
  • Create New...