Jump to content
SAU Community

R34 Gtr Double Din Conversion Kit - Part Numbers?


Recommended Posts

The photo I posted is one with ambient temp.

You could change the face plate, but is it easy to find?

The climate control unit is only $150 and it's plug and play so I just thought itd be the best and easiest method.

Link to comment
Share on other sites

  • 1 month later...

Hi everyone,

Have just finished sourcing all of the required parts for this conversion.

For future reference, if anybody has the same factory GTR NAVI unit as mine - for clarification, the side brackets are definately different and you need to also source the double din brackets.

If anybody is actually interested in a full kit - PM me as I have one with everything you need which I am thinking of selling - Brackets, brand new genuine nissan double din facia / surround, air con unit with brand new genuine nissan replacement front face. The whole kit literally looks brand new.

I'm still tossing up whether to put it in my car or not.

Cheers.

Link to comment
Share on other sites

  • 3 months later...

anyone still able to supply these brackets with the climate control unit? been looking to do the double-din conversion on mine for a while been chasing the parts.

Link to comment
Share on other sites

  • 1 month later...

Its already double din iso ( tiny bit off double din todays standard but not much to worry about )

No kit needed but some trim rings wont fit right without filing the trim ring slightly or some dont need trim ring mounted , only slot the existing holes in the cage holding the radio to set it back a bit further to make it look perfect

Note tape a thick soft towel around the console / gear surround to set the razor sharp cage on or it farks the surround black bits and its near impossible to repair ,

Double din rules fark the single din look is boring

made this mistake doing my double din conversion drunk, was too over excited when it finally got delivered now scratches everywhere :( will probably get it repolstered

Link to comment
Share on other sites

  • 2 weeks later...
  • 5 years later...

I would be interested in purchasing any of the mentioned parts including the 2 DIN brackets and the facia and the new faceplate for the ambient control version of the heater control.  My gtr has the sat nav aswell and I'd like to convert to the 2DIN setup.

Thanks! 

Sean

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
    • Nah, im after the more newer looking, one with the OLED display
    • We revised the neutral wire instructions. The old way was wrong.  R34 gearbox change.pdf
×
×
  • Create New...