Jump to content
SAU Community

Ame Tm02 Tracer Wheels. 18X10+15 ( Used ) And 18X11+10 ( New )

JET200
 Share

Recommended Posts

JET200 Proficient

JET200

Posted
Posted

I bought two sets of wheels for JET200 but realised, its a bit excessive so have decided to sell one of the sets.

A pair of 18x10+15mm used set for the front in good condition. Been used for one track day

A pair of 18x11+10mm brand new in the box.

The 10s cost $612.50 each from Autotechnik ( where I go them )

And the 11s are by order only and cost over $750 each new ( as these ones are )

After $2100 for the lot. Essentially your paying for 3 and getting 4th free

Pick up in Silverwater NSW or post at buyers expense

post-60913-0-72298500-1345194535_thumb.jpgpost-60913-0-85418800-1345194530_thumb.jpgpost-60913-0-99341100-1345194541_thumb.jpgpost-60913-0-37366600-1345194509_thumb.jpgpost-60913-0-45434900-1345194552_thumb.jpg

post-60913-0-59189600-1345194546_thumb.jpg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • deev236
      Stagea S2 RS Four S Misfire/Rough Idle

      By deev236 · Posted

      And by the way, I've also checked the ECU diagnostic numerous times and got a bad O2 sensor code and initially an Ignition Primary code, which is why I replaced the O2 sensor and all the ignition components (coil packa, plug and loom). No codes have been coming up lately despite the ongoing issue.
    • deev236
      Stagea S2 RS Four S Misfire/Rough Idle

      By deev236 · Posted

      Hey pber13, unfortunately still no luck. At this point the following has been done with little or no success: - Spark plugs replaced, gapped to 0.8mm - Splitfire coilpacks installed to replace originals - Replaced Ignition Coil/Coilpack harness with a new genuine nissan one - New fuel filter - Replaced AFM/MAF sensor - Injectors have been thoroughly cleaned with an online flush (without removing) - Upper engine and inlet decarbed - blew tons of black smoke out, cleared the carbon deposits from the top of the engine and exhaust.  - IACV removed and thoroughly cleaned with carburettor cleaner - O2 sensor replaced with new and genuine one -  Smoke test revealed no vacuum leaks - Healthy compression test of 160psi across all 6 cylinders Overall the car does run a lot smoother now, no backfires between gear shifts like it did originally... but the rough idle when warmed up is still there. It may not even be a misfire but simply a rough idle. Seems crazy to me that so many people have had this issue and seemingly no one has gotten to the bottom of it, or at least never bothered to post if they did! Hope you have more luck than I did pber13, I'm at a point now where I'm just going to try to ignore it unless it gets worse. Would love to fix it but I've genuinely run out of ideas of what it could be.
    • R3N3
      AC Compressor

      By R3N3 · Posted

      I got the full frenchys kit too. Really awesome kit. Easy to install my only complaint was the hardlines I think could be routed differently (I modified mine) but I realise the kit needs to suit multiple applications. This was the hard lines before I modified them. They were touching the wastegate pipe. I ended up reducing the distance between firewall and first bend. The made it so they tucked along the frame rail.
    • pber13
      Stagea S2 RS Four S Misfire/Rough Idle

      By pber13 · Posted

      Deeve, I don't suppose that you've made any progress on this? My Stagea has the exact same problem, and just like you, I've read through as much as I can online, with no real progress. My car isn't throwing any codes at all, which is a little frustrating. I've changed plugs, checked the wiring and harness. A new MAF gets here next week, but I'm not hopeful it will solve the issue.
    • Butters
      AC Compressor

      By Butters · Posted

      I installed it all myself,  It was really easy to install.  I got a professional to do the degas/gas.
×
×
  • Create New...