Jump to content
SAU Community

Recommended Posts

As long as you have safety bars in place at the right height, you're not going to break your neck. The body tips over forward and you end up on your knees with the safety bars taking the load, before this happens.

If you feel like this, you need to tilt the head up higher, chest out further and shoulders back further.

yeah I used to get that a bit until I started really using my rear end to power up, and stopped wearing heeled shoes

I wear powerlifting shoes, so maybe I need to focus on using my rear to power up as you say if I start squatting again.

I wear powerlifting shoes, so maybe I need to focus on using my rear to power up as you say if I start squatting again.

If you are tipping forward when coming up, it means that your hip/rear is already rising faster than you can handle.

you either lack upper back strength or need to practice squatting more upright.

Front squats are good for this.

If you are tipping forward when coming up, it means that your hip/rear is already rising faster than you can handle.

you either lack upper back strength or need to practice squatting more upright.

Front squats are good for this.

I tried to do front squats as I cant back squat due to my injury but I couldn't even front squat the bar. Can't seem to get any upper body strength going on.

Sorry I didn't know you had an injury.

Why couldn't you squat just the bar? too heavy or injury related? mobility?

yeah too heavy, I just couldn't get the mechanics of balancing the bar in front of me.. yet I was back squatting 65kg

You should easily be able to front squat the bar. Keep your head and elbows high.

Just try bw with a broomstick til you get comfortable doing it

Edit: TTT suggested broomstick as well, great minds think a like

Crossed arms sucks, I prefer the other way

Edited by Mitcho_7

Yeah tipping forward. Birds would be able to explain it better than me

Only seen you attempt it once and I forget where the point of failure was.

I'm not very good at front squats myself...arms don't quite have the flexibility for it yet.

I actually find front squat positioning/mechanics much easier to get good depth but obviously cant do as much weight.

Keeping your elbows high and head up are really the only cues I use. As soon as the elbows drop its about 20x harder I find

Edited by Mitcho_7

my injury is between L5 and S1 so even though I wear a belt it, I can't get it low enough to support that area. It's right down at the top of my glutes.

what TTT said about falling forward is really good advice. It took me a long time to learn how to sit back into a squat and use my glutes instead of shifting my weight forward and using my quads.

I was a lot stronger squatting from my quads in the beginning. Any time I felt the weight get heavy I was shifting weight onto my toes. Wasn't helped by the oly shoes I was wearing. This was until I started having crippling knee pain. Its was so bad I was hobbling around and couldn't sit for long periods without them aching.

So I ditched the oly shoes and practiced sitting back, having the weight on my heels. I would actually lift my toes off the floor as I squatted to make sure I didn't come forward. Later I also switched to a low bar position which also helped and I do a lot of front squatting as assistance. Very difficult to not sit back when front squatting as TTT suggests.

This fixed my knee pain but makes it really hard to buy pants/shorts as my ass is heaps bigger! lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
    • I _think_ that one has a christmas tree or some other retainer spike into a hole in that panel under it. Come in under it with thin scredrivers and just pry it gently up. If you rip the ears off the retainer pin....so what? Just stick it back down after with a bit of race tape and carry on with life.
×
×
  • Create New...