Jump to content
SAU Community

Recommended Posts

Car: 2000 R34 25GT N/A

Trans: 5 speed manual

Problem: Extremely hard to get into gear when cold and very notchy till she is fully warmed up.

Car was brought into Aus in March 2013 and complianced and registered in May 2013. Presumed mileage on the paperwork I have was 70,331km. I am second owner in Aus. According to the paperwork I have all fluids were changed. I have checked the level in the gearbox and it it fine. However the oil put in smells like normal 80w 90 MINERAL oil which I know is not correct. I want to change oil but my question is what if any damage may have been done to the gearbox since I have had the car. Problem as I said is only when cold and motor running. Clutch feels good and seems to be releasing properly. Any thoughts appreciated.

Link to comment
https://www.sau.com.au/forums/topic/437422-gearbox-problem/
Share on other sites

You have wrong or crap oil in gearbox.

Drop oil with either

VMX 80 and nulon gearbox treatment

or

Smurfs blood

IT will only cost you 30 odd for the castrol oil and you will be able to tell if it is better. IF not then you have to do more fault finding. Taking gearbox out n shit

Link to comment
https://www.sau.com.au/forums/topic/437422-gearbox-problem/#findComment-7166459
Share on other sites

Thanks fellas. Will check the clutch freeplay as well but it seems to be fine. Pretty sure its the wrong oil. Smells the same as the 80m90 shit you put in the old ford and holden gearboxes and diffs. Stupid flaming Indians.

Link to comment
https://www.sau.com.au/forums/topic/437422-gearbox-problem/#findComment-7166783
Share on other sites

Normaly its a sign that the oil used is too thick.

Years ago some Toyota boxes were like this from factory, very hard to shift and notchy when cold, the repair bulitin was to run a thinner oil in them.

Link to comment
https://www.sau.com.au/forums/topic/437422-gearbox-problem/#findComment-7166810
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...