Jump to content
SAU Community

Heavy Steering And Hicas Warning


Recommended Posts

  • 6 months later...

Hi,

For anyone still interested in this, I had the same issue for the past four years on my 1994 R32 GT-R. The HICAS light would come on a few minutes after driving and the steering would go dead heavy.

I had Nissan and another workshop run the HICAS diagnostics multiple times - no problems: the back wheels did their flappy thing and everything.

Finally, just this week Custom Importz in Lonsdale SA found and fixed the problem. There were actually three faults:

1. The speed sensor in the back of the instrument cluster was faulty.

2. The steering angle sensor was faulty

3. (Not such an issue). One of the rear solenoids was faulty (this did show in up diagnostics but replacing it not fix the issue until the above two were fixed).

For anyone having this problem, follow the advice above to run the HICAS diagnostics, check fluid levels etc, but also get your shop to check these sensors in around the console and steering column. They were the "missing link" that did not show up in diagnostics.

Glenn

Link to comment
Share on other sites

No, the HICAS solenoids are the big arse lumps just in front of the driver's side axle.  Hydraulic pipes coming down the chassis rail to them from the front, flexibles going out of them to the HICAS rack.  This image of an S13 shows it, correctly named, as the "fail-safe valve".

hicas1.jpg

 

Link to comment
Share on other sites

And following up on Glenn's update......looks like Missileman was on the money with the speedo.

It will come to the point where we will need to look at wiring diagrams for non-HICAS Nissans of the era to work out how they ran their power steering assistance control without a HICAS computer, so we can delete the troublesome buggers of things when even the usual bypasses we do stop being good enough.

Link to comment
Share on other sites

I'm trying to figure out why my steering is heavy at low speed.

So far I have figured out the speed out of my cluster is fluctuating around 10kmph or so (looking at the software on my link ecu) Also measuring the yellow/green wire at the Hicas ecu the volts are fluctuating at a constant speed.

Could this fluctuating be causing the hicas to stop adjusting the valve in the steering rack?

Glen did you have to replace the whole cluster or can the speed sender be replaced on it's own?

I tried many times to get the car to enter diagnostic mode but it wouldn't do it..

Cheers!

 

Link to comment
Share on other sites

The speed signal from the speedo head to the ECU and to the HICAS CU is a square wave 0-[something, I think 5] volt PWM signal.  You will see it vary under normal circumstances.  But I suppose the speedo head could fail in a way that the indicated speed is fixed, or never goes low enough to boost the assistance.

Look at the R32 GTR workshop manual pdf for guidance on how the AC speedo sensor signal is converted to the square wave signal and what you should see at various road speeds.  Then use a scan tool to interrogate the HICAS CU for what it's seeing.

Link to comment
Share on other sites

Thanks for the reply.

There is probably nothing wrong with my speed sensor (I just assumed that the reading fluctuating so much indicated a problem) and my Hicas issue is most likely something else. 

Cheers

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Euros are shitboxes man. My next car going to be a Lexus or Hyundai.
    • Maybe I used the wrong sandwich plate as well. Used one piece instead of two piece.  
    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
×
×
  • Create New...