Jump to content
SAU Community

whos in townsville its time to get it rockin


AZZA
 Share

Recommended Posts

Hi all i have been in the vill for 4 yrs now but until recently didnt own a skyline. In saying so i have recently joined this forum site and was wandering who is in the vill.

As although there are plenty of skylines owners here i dont know any of them.

I was hoping to get something organised, or get a group of enthusiest's together to liven up the place, or if thats already going then who should i contact to let the good times flow. :D

Link to comment
Share on other sites

I have just moved up from brisvegas. Would be great to get something organised. Have a few good events in brissie but have not heard of much up here.

Sounds good mate will have to try to get something going, i dont know how successful we will be, but i know you only have to pay about $20 to take your car down the 1/4 mile when its running. how about we arganise that as our first event. Or theres always the possibility of a roud run.

Link to comment
Share on other sites

I used to live up there , there are some nice new straight roads on the way to Charters if you wana test your speed , but yeah if you want to cruise not much else but Paluma

Link to comment
Share on other sites

  • 3 months later...

Hey guys, i used to live in tsv, and will be back again at the end of the year. I would also like to find someone in tsv or cairns region that has a 4 door R34 for a wedding car around middle of next year. Unless someone has one for sale ????

Also I'm a member of a good car club that does cruises every 2 weeks. "Pulse" (www.pulsemotorsports.net.tc)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • I visually inspected the threads and they look intact and not so dirty, so I don’t understand why they wouldn’t thread in straight.    How would a chaser cause any damage? It’s intended to clean up the threads right? Even if it was cross threaded. That shouldn’t be the case though because the studs that were removed were OEM. The intake side had no issue. 
    • Well, try the new studs first, in case the US sourced studs are actually the problem. But given that the head is off the engine, at least it won't be too hard for someone to install helicoils if it turns out the holes are stuffed. You don't want to just run a tap or chaser through there if by doing so you leave behind 3/10ths of f**k all thread and the studs just pull straight out when you torque up the manifold nuts.
    • Hey everyone, I’m having a bit of a crisis and would like some advice.  I am in the process of assembling a head I had gotten back after NAPREC did their work. I had the exhaust studs removed prior to sending it to the machine shop, but afterwards when I tried threading in new studs, they wouldn’t go in straight. They would thread in smoothly by hand with almost no effort, but it doesn’t go in straight (noticeably circular motion) and eventually stops about halfway in. I had a couple go in perfectly straight with no effort, but when I removed them to try it again, they no longer when in straight and had the same issue as the others. The studs I’m using are M8x1.25, which I read was the standard. I did some research and decided to buy a chaser kit and new studs IEE NZ just in case. Has anyone experienced this? How screwed am I? Do I just need to run a chaser or tap and try again? Prefer a chaser because I heard taps can destroy existing threads.    Note: I also have a new set of intake studs that went straight in just fine that I bought from IEE NZ. I bought the exhaust studs from the U.S.
    • Photos. What you describe sounds impossible, given how the arms are assembled to the upright.
    • Hello everyone.  Since the last stint of turbo upgrades, the intake plumbing from air filter to turbo was made up of sections of ally pipe and silicone bends. This was done as the stock suction pipe was so restrictive, it was noticable on the dyno. The configuration and layout of the m35 engine bay meant that the intake plumbing was too close to the exhaust manifold, even in contact with the heat sheild in one spot. Apart from that i had to use the first section of the stock suction pipe bolted onto the turbo. Although the setup was much better than the stock suction pipe, it still caused some restriction and excesive heat into the incoming air. Its like trying to suck a thickshake through a thin soft drink straw, possible, but you gotta work really hard. Then add the heat...for those that may not know, the hotter the air, the further the oxygen molecules are apart and the less explosive a given area of air is when mixed with fuel, hence, why intercoolers work (compressing air makes the molecules move faster which also generates heat). Water injection and nitrous oxide injection also use the same principle.  As the M35 Stagea intake and suction pipe options on the market are very very limited, i decided to fabricate my own from the turbo to the filter and include one silicone joiner to allow for engine twist.  If anyone is interested while I'm in the process, I could manufacture a couple more but you gotta let me know soon. I'll post some pictures soon.
×
×
  • Create New...