Jump to content
SAU Community

Bilstein Shocks, Apexi Power Fc For Ecr33 Rb25, Top Feed Fuel Rail, Splitfire Coilpacks [syd]


Recommended Posts

Have decided today that I will part out some parts in the car so the following items are for sale:

Bilstein shocks- Car handled really well with them, great for street cars and occasional track days.

Suits: 4wd Skyline / stagea models with eye mount at the rear. eg GTS4 GT4

Condition: Good condition, No leaks, fronts are only 5000km old, rears are about 15000km with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $350 for the set

Apexi Power FC for R33 GTS-t with EL Controller- Good reliable cheap plug and play alternative compared to most other ECUs.

Suits: R33 GTST, S1 Stagea with RB25DET

Condition: Only roughly 9 months old, latest model, in almost brand new condition

Also Included: EL hand controller, Box and all instructions included

Price: $990

Top Feed Billet Fuel Rail for R33 GTS-t- Does not require modification to the stock plenum, makes top feed conversion a walk in the park. It is set up as a single entry fuel rail but you also have the freedom of converting it to twin entry if you wish- just undo the top cap

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Suits: Bolt-on fuel rail for R33 RB25 top feed conversion, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $150 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Splitfire Coilpacks- engine runs smooth and strong @ 280rwkw with them

Suits: series 2 R33 GTST RB25 and R34 GTR RB26,

Condition: as new condition, only had them for roughly 5000km as well.

Price: $300

Located in North Sydney, pick up available, shipping @ buyers expense.

PM me if interested.

Edited by chiksluvit
Link to comment
Share on other sites

The photos for power fc

This is the latest PFC for ecr33 with EL commander and additional tuning load vs timing feature. The EL hand controller has improved visibility.

Comes with box, original packaging etc, only used for roughly 9 months

Edited by chiksluvit
Link to comment
Share on other sites

One thing I'd like to add:

I have been very reasonable with the price of items that I have listed- a few of them being half or less than half of what I have paid for. They are not old parts either, most items have only been bought for 6~9 months and limited usage

so please, no unreasonable offers

Link to comment
Share on other sites

PFC Sold!

Items still available for sale:

Bilstein shocks- Car handled really well with them, great for street cars and occasional track days.

Suits: 4wd Skyline / stagea models with eye mount at the rear. eg GTS4 GT4

Condition: Good condition, No leaks, fronts are only 5000km old, rears are about 15000km with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $350 for the set

Top Feed Billet Fuel Rail for R33 GTS-t- Does not require modification to the stock plenum, makes top feed conversion a walk in the park. It is set up as a single entry fuel rail but you also have the freedom of converting it to twin entry if you wish- just undo the top cap

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Suits: Bolt-on fuel rail for R33 RB25 top feed conversion, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $150 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Stock Fuel Pressure Regulator adapter for external mounting- Good for RB25 top feed conversions without having to buy another reg
Suits: Nissan RB SR fuel regulator - maybe other cars too like subaru wrx but I'm not 100% sure

Also Inculded: Dash 6 male fitting
Does not come with the fuel regulator
Price: $40

Splitfire Coilpacks- engine runs smooth and strong @ 280rwkw with them

Suits: series 2 R33 GTST RB25 and R34 GTR RB26,

Condition: as new condition, only had them for roughly 5000km as well.

Price: $300

Edited by chiksluvit
Link to comment
Share on other sites

Front Bilsteins Sold!

rear pair still available @ $100 for the pair

Items still available for sale:

Bilstein shocks rears only- Car handled really well with them, great for street cars and occasional track days.

Suits: Skyline / stagea models with eye mount at the rear. eg GTST, GTS, GT, GTS4, GT4

Condition: Good condition, No leaks, rears are about 15000km with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $100 for the pair

Top Feed Billet Fuel Rail for R33 GTS-t- Does not require modification to the stock plenum, makes top feed conversion a walk in the park. It is set up as a single entry fuel rail but you also have the freedom of converting it to twin entry if you wish- just undo the top cap

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Suits: Bolt-on fuel rail for R33 RB25 top feed conversion, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $150 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Stock Fuel Pressure Regulator adapter for external mounting- Good for RB25 top feed conversions without having to buy another reg
Suits: Nissan RB SR fuel regulator - maybe other cars too like subaru wrx but I'm not 100% sure

Also Inculded: Dash 6 male fitting
Does not come with the fuel regulator
Price: $40

Splitfire Coilpacks- engine runs smooth and strong @ 280rwkw with them

Suits: series 2 R33 GTST RB25 and R34 GTR RB26,

Condition: as new condition, only had them for roughly 5000km as well.

Price: $300

Link to comment
Share on other sites

http://www.sau.com.au/forums/index.php?/topic/403711-Top-Feed-Rail-In-R33-With-Stock-Plenum%2E%2Eyes-It-Can-Be-Done/page__view__findpost__p__7421431

Above is a link to the guide on how to install the top feed fuel rail with 1/2 height injectors. The fuel rail is exactly the same as what Johnny has except for the colour, so you will be able to go by this guide when doing the conversion.

Link to comment
Share on other sites

Have pulled the rear shocks out, washer on strut top isn't in the best condition and the top of one of the shaft is rounded.

Top nut isn't frozen and there are no leaks however. It has been loosened so you can swap the springs over or to adjust the height

In light of the condition, Price of bilstein rear suspension is now dropped to $50, includes GTR rear springs and strut tops

post-27668-14222452150874_thumb.jpg

Link to comment
Share on other sites

Just tidying this thread up and price updates- price drop on most items refer to below

Bilstein shocks rears only- Car handled really well with them, great for street cars and occasional track days.

Suits: Skyline / stagea models with eye mount at the rear. eg GTST, GTS, GT, GTS4, GT4

Condition: No leaks, one of the shock shaft is rounded at the top, top nut is loosened however. has with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $50 for the pair

post-27668-14222452150874_thumb.jpg

Top Feed Billet Fuel Rail for R33 GTS-t- Direct bolt on to the stock plenum, makes top feed conversion a walk in the park.

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Follow this link for installation instructions, it is the same kit as Johnny's http://www.sau.com.au/forums/index.php?/topic/403711-Top-Feed-Rail-In-R33-With-Stock-Plenum..yes-It-Can-Be-Done/page__view__findpost__p__7421431

Suits: Bolt-on fuel rail for R33 RB25 stock plenum, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $130 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Stock Fuel Pressure Regulator adapter for external mounting- Good for RB25 top feed conversions without having to buy another reg
Suits: Nissan RB SR fuel regulator - maybe other cars too like subaru wrx but I'm not 100% sure

Also Inculded: Dash 6 male fitting
Does not come with the fuel pressure regulator
Price: $40

post-27668-14220567738421_thumb.jpg
post-27668-14208458034646_thumb.jpg

Splitfire Coilpacks- engine runs smooth and strong @ 280rwkw with them, update your old tired coilpacks, fixes the common misfire on boost issues

Suits: series 2 R33 GTST RB25 and R34 GTR RB26

Condition: as new condition, only had them for roughly 5000km as well.

Price: $250

Edited by chiksluvit
Link to comment
Share on other sites

Coilpack sold

Bilstein shocks rears only- Car handled really well with them, great for street cars and occasional track days.

Suits: Skyline / stagea models with eye mount at the rear. eg GTST, GTS, GT, GTS4, GT4

Condition: No leaks, one of the shock shaft is rounded at the top, top nut is loosened however. has with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $50 for the pair

post-27668-14222452150874_thumb.jpg

Top Feed Billet Fuel Rail for R33 GTS-t- Direct bolt on to the stock plenum, makes top feed conversion a walk in the park.

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Follow this link for installation instructions, it is the same kit as Johnny's http://www.sau.com.au/forums/index.php?/topic/403711-Top-Feed-Rail-In-R33-With-Stock-Plenum..yes-It-Can-Be-Done/page__view__findpost__p__7421431

Suits: Bolt-on fuel rail for R33 RB25 stock plenum, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $130 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Stock Fuel Pressure Regulator adapter for external mounting- Good for RB25 top feed conversions without having to buy another reg
Suits: Nissan RB SR fuel regulator - maybe other cars too like subaru wrx but I'm not 100% sure

Also Inculded: Dash 6 male fitting
Does not come with the fuel pressure regulator
Price: $40

post-27668-14208458034646_thumb.jpgpost-27668-14220567738421_thumb.jpg
Link to comment
Share on other sites

Just gone through my box of parts and found an unused fuel rail for GReddy plenum- will throw this in the sale with the other fuel rail

Bilstein shocks rears only- Car handled really well with them, great for street cars and occasional track days.

Suits: Skyline / stagea models with eye mount at the rear. eg GTST, GTS, GT, GTS4, GT4

Condition: No leaks, one of the shock shaft is rounded at the top, top nut is loosened however. has with circlip groove machined for height adjustment.

Also Included: Suspension top mount, stock R33 GTR rear springs (slightly higher spring rate than GTST).

Price: $50 for the pair

Top Feed Billet Fuel Rail for R33 GTS-t- 2 rails included- one for Direct bolt on to the stock plenum, makes top feed conversion a walk in the park; the other is one that works with GReddy plenum, brand new never used so you can choose the right rail for your application

You will only need to get the injectors and some fuel hose if you use this kit for the conversion- will save you a lot of pain and headaches

Follow this link for installation instructions, the bolt on rail is the same kit as Johnny's http://www.sau.com.au/forums/index.php?/topic/403711-Top-Feed-Rail-In-R33-With-Stock-Plenum..yes-It-Can-Be-Done/page__view__findpost__p__7421431

Suits: Bolt-on fuel rail for R33 RB25 stock plenum, using 1/2 height top feed Bosch EV14s or Siemens Deka injectors,

Also Inculded: Cap and fitting for the top fuel exit and fittings on both ends, plenum spacers for the rail, spacer for 14mm injectors, 14mm to 11mm injector top hats

Price: $130 - will also throw in a generic fuel pressure reg for free. Been using this on a 280rwkw setup with no issues.

Stock Fuel Pressure Regulator adapter for external mounting- Good for RB25 top feed conversions without having to buy another reg
Suits: Nissan RB SR fuel regulator - maybe other cars too like subaru wrx but I'm not 100% sure

Also Inculded: Dash 6 male fitting
Does not come with the fuel pressure regulator
Price: $40

Edited by chiksluvit
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



×
×
  • Create New...