BK Posted September 13, 2018 Share Posted September 13, 2018 For sale is a lot of new and used RB26 and GTR parts that need to go. Got way too much stuff and don't have the space. Photos will be updated regularly (and tell me if I've forgotten to upload something). All used parts in good condition - I am a hoarder of parts as most GTR owners are. Contact to arrange postage as I am in Alice Springs, NT, but will freight stuff anywhere. All prices negotiable to some degree so make me an offer ! Precision ball bearing Gen1 6266 turbo T4 divided 0.84 a/r SP cover - requires rebuild on chra, Slightly passing oil but will smoke if used, otherwise ok. Can be rebuilt locally by Rose rage turbos or sent back to Precision - $1100 Trust T78-29D turbo, T4 divided - requires rebuild on chra. Same as above passing some oil on seals. Easy to rebuild with genuine Mitsubishi parts - $900 NPC 10" single plate push clutch rated to 450kw. NPC7056B-10 Good condition, suit all RB push setups - $700 RB26 R33 flywheel - $200 NEW Prosport 60mm dual stepper motor type JDM series 40psi electronic boost gauge with pressure sensor, harness and 60mm gauge cup. Has dual analogue needle and digital readout, programmable warning light. - $220 Used BPP 14mm twin entry fuel rail - $150 Used Nissan RB26 90A alternator - $150 Used standard R32/R33 GTR blow off valves - $150 Used Turbosmart FPR800 adjustable fuel reg in blue. Fitted with AN6 male flare inlet and 5/16" hose barb outlet fittings - $150 Used BNR32 front upper control arms - $150 Used RB26 lower front belt timing cover - $50 2 X New RB26 genuine NIssan head gasket 11044-05U16 - $90 each (rrp $130) 60mm electronic boost gauge, 1.6bar max with MAP sensor. 60mm gauge cup included. Remote peak / hold controller - $90 3 x R34 GTR lower shifter bush - $10 each. R32 / R33 GTR pull clutch slave cylinder and hose - $90 Used Rear R33 GTR sway bar - $90 (Good S14 or S15 upgrade) NEW R33 GTR / GTS25T STS Performance (made in UK) 3 ply silicone lower radiator hose in RED from GCG turbos (not chinese ebay crap) - $45 Used R32 GTR front diff centre - $200 USED RB26 LONG NOSE CRANK - $600 Carbon fibre N1 bootlip spoiler -$250 FRP N1 bootlip spoiler in TH1 blue - $200 SARD / DENSO 1000cc injectors. Low impedance , 0.85ms latency. Fit 10.5mm (standard) or 11mm fuel rail. - $450 Tomei RB26 sump baffle - $150 Nitto 2.8 billet 4340 steel full counter stroker crankshaft - 77.7mm. Done 600km from new. Not used since regrind to mains (10thou) -0.25mm and big ends (20thou) -0.50mm. Rebalanced, crack tested, checked for straightness and journal hardness by Rick Corbett Engineering in Adelaide 19th. November 2018 - $2900 ono (worth $5600 new + $500 machine work.) - SOLD HKS T51S v band in / out ex housing 1.00 A/R Turbo (based on Garrett TA51 / TA45S). Comes with T4 to HKS 99.1mm V-band manifold flange adaptor (these are rare as hens' teeth) and HKS 115mm turbine v-band flange and clamps. Made 500+kw on 98ron - $1450 - SOLD Camtech CT3536/37 445B R32 / R33 RB26 inlet / exhaust camshafts - 272 deg. 9.7mm lift. Trial fitted only. - $750 - SOLD HKS EVC III boost controller complete with instructions. Max boost 2.0 bar - $250 - SOLD HKS EVC IV boost controller complete with instructions. Max boost 2.5 bar - $270 - SOLD Used genuine R32 / R33 RB26 CAST ALLOY upper timing gear cover - $450 (These are now worth $900+ new) - SOLD NEW genuine Nissan 31 tooth spline rear diff half shafts (Suit Quaife or OS Giken rear diff upgrade for pre 94 R32 GTR which is 30t standard) - $900 - Almost impossible to obtain now - SOLD 2nd set of NEW genuine Nissan 31 tooth spline R32 / R33 GTR rear diff half shafts (Suit Quaife or OS Giken rear diff upgrade for pre 94 R32 GTR which is 30t standard) - $900 - Almost impossible to obtain now. Will be the last set ever I obtain. - SOLD Modified R32/R33 transfer case. 10 clutch plate (standard is 7 plate) Racepace / Midori Sebei / AGY style upgrade. Fully rebulit back to factory 0.2 - 0.5mm clutch pack clearances when clutch pack was modified (new retaining pressure plates, clutch plates, oil pump o-rings, strainer filter, ect). - $1900 ono - SOLD 2ND Modified R32/R33 RB26 GT-R transfer case. 10 clutch plate (standard is 7 plate) Racepace / Midori Sebei / AGY style upgrade. Fully rebulit back to factory 0.2 - 0.5mm clutch pack clearance. This one is at 12 thou / 0.305mm with a 5.0mm rear and 5.4mm front retainer plates - $2100 - SOLD Tomei rb26 type B valve springs with retainers. Done about 1000km - $450 - SOLD Nitto RB head drain with 5/8" push on fitting - brand new ! - $185 - SOLD Used Trust NS1310G 13 row oil cooler. 300 x 185 x 50mm with -AN10 fittings - $200 - SOLD ARP RB26 main studs. Done about 1000km - $150 - SOLD NEW 6 x 11mm Golebys bosch EV14 injector adapters with o-rings - $70 - SOLD NEW R32 GTR genuine Nissan Pitwork power steering belt 4PK950. Trial fitted only as now have Ross balancer and need 4PK925 so it's too long. - $30 - SOLD Used R33 GTR genuine rear upper control arms - bushes intact - $50 - SOLD Used R32 GTR genuine rear upper control arms - bushes intact - $50 - SOLD Used RB26 crankshaft lower timing belt gear - $70 (worth $170 new) - SOLD Used Link G4 plug in GTR ECU fitted in R32 GTR ECU case - $1500 - SOLD Used 6 X Bosch 2000cc injectors with 14mm full length adaptors - $400 - SOLD NEW R32 / R33 SKYLINE AND GTR GEARBOX SHIFTER LOWER BOOT 74967-05U00 - $50 (rrp $70) -SOLD NEW Skyline BCNR33 GTR and ECR33 GTS25t heater blend air mix actuator 27732-15U01 (one of the two causes of that stupid R33 aircon fan clicking sound common fault) - $220 - SOLD USED R32 GTR ROSS TUFFBOND METAL JACKET HARMONIC BALANCER - $550 Like new. Done 1000km - SOLD Race clutch by Jim berry full monty 4000lb 5 puck push style race clutch. Comes with push release bearing and correct 16mm bearing carrier- $1300 (Slightly used - has less than 0.5mm wear) - SOLD 2 x R32/R33 GTR splitfire coilpack sets SF-DIS-001- $300 each - SOLD R32 GTR interior clock - DOESN'T WORK for parts only - $50 - SOLD TRUST / Greddy RB26 R32 / R33 GTR extended sump with pickup and baffle. Ready to bolt on - $800 - SOLD HKS DLI twin power with R32/R33 GTR plug in harness 43001-AK001- $450 now discontinued - SOLD Forged CP pistons 86.5mm with used rings less than 500km - $600 - SOLD Crower I-beam billet steel conrods - $1000 used but almost like new (Cost me $2200) - SOLD RB starter motor from R32 GTR - $150 (new ones are $700) - SOLD Nitto 86.5mm 2.8l stroker pistons - $1000 used but almost like new (must be used with Nitto 2.8 crank as piston pin height is different to standard) - SOLD Nitto 121.5mm billet steel I-beam conrods - $950 used but almost like new - SOLD Nitto oil pump - $1000 used but like new - SOLD Apexi Power FC boost control kit - 3 pin 415-A001- $350 (suits R32/R33/R34 GTR, early S14, R33 GTS25t Skyline) - SOLD Apexi D-Jetro Power FC with new type EL type hand controller 414BN035 - $1250 includes 2 x APEXi (Denso) 3 bar MAP Sensors (499-X001) 1 x MAP Sensor Harness (415-XA04) - SOLD R32 GTR R200 30 tooth spline rear diff half shaft pair - $400 (used in Nismo GT diffs) - SOLD BARELY USED R33/R34 GTR RB26 genuine long nose crank fully balanced - $1200 used but almost like new. Has had $500 of machine balancing for high RPM - REPORT AVAILABLE (Just crank new is $1900 rrp) - $1250 - SOLD R33 GTR converted to push type gearbox rebuilt with replaced synchros - $1450 Not used since rebuild. Still in shed not fitted. Fitted with R32 transfer case. - SOLD 4 x R32 GTR 16 x 8 wheels with 255/50 Mickey Thompson ET street drag radials. - $900 - SOLD R32 GTR mechanical LSD rear diff centre. Suit 30 tooth spline - $195 - SOLD R32 GTR rear diff cover (89 - 92 early type - finned) - $120 - SOLD Used HKS purple alloy oil filler cap - $30 - SOLD NEW ARP RB26 flywheel bolts - $75 -SOLD Used R32 GTR / GTSt adjustable rear upper control arms - $60 - SOLD NEW genuine NISMO 1.3 bar radiator cap - $50 - SOLD Used Nismo 65deg C low temp thermostat - $40 suits all RBs - SOLD NEW TOMEI 1.5MM BLOCK RESTRICTOR - $10 - SOLD R33 GTR standard ECU - $150 - SOLD NEW NISSAN 14mm PUSH CLUTCH RELEASE BEARING SLEEVE / CARRIER 30501-N1604 (rrp $50) used on a lot of multi plate clutches. CARRIER ONLY (suits most multi plate clutches out there eg. Exedy Hyper Twin ) - $40 - SOLD Used 18mm push clutch release bearing carrier and release bearing 30501-S0260 / 30501-S0200 (used on standard R32 GTR, OS GIKEN R4C, TS3B clutch and other multi plate clutches) - $50 - SOLD Used 26mm push clutch release bearing carrier and release bearing 30501-K0510 (used on OS GIKEN R3C and R3B clutch and other multi plate clutches) - $50 - SOLD OS Giken OS-88 direct shifter with gearknob - (shifter only, no retaining rings) - $100 -SOLD Trust / Quaife 3F1 6 speed H pattern straight cut dog box with freshly modified 10-plate transfer case. $8300 ono - SOLD OS GIKEN 5 speed transmission. Uprated 24t OS input shaft. New Updated R33 GTR series 3 synchros and selector forks. Push type clutch release. R32/R33 GT-R transfer case. Business only addresses only- $6000 - SOLD Will list more as I get the time. Contact Ben on 0401 779 905 OS GIKEN 5 SPEED TRANSMISSION WITH R32 GTR TRANSFER CASE R32 GTR REAR MECHANICAL LSD DIFF CENTRE - 30 TOOTH SPLINE R32 / R33 GTR FRONT OPEN DIFF CENTRE RB26 86.5MM CP FORGED ALUMINIUM PISTON SET RB26 CROWER BILLET STEEL I BEAM CONRODS WITH CROWER ROD BOLTS NITTO / JE FORGED ALUMINIUM 2.8L 86.5MM PISTON KIT RB26 LOWER TIMING BELT COVER NITTO RB26 BILLET STEEL I BEAM CONRODS WITH ARP 2000 ROD BOLTS RB26 GTR LONG NOSE FULLY BALANCED CRANKSHAFT R33 GTR 5 SPEED TRANSMISSION - FULLY RECONDITIONED R32 GTR REAR UPPER CONTROL ARMS - GENUINE STANDARD R33 GTR AND GTS25T HEATER MIXER - BRAND NEW. FIX THAT STUPID CLICKING SOUND IN YOUR R33. R33 GTR REAR UPPER CONTROL ARMS - GENUINE STANDARD NISSAN NEW R32 / R33 SKYLINE AND GTR GEARBOX SHIFTER LOWER BOOT NEW NISSAN 14MM PUSH CLUTCH RELEASE BEARING SLEEVE NITTO 77.7MM 2.8 BILLET FULL COUNTER STROKER CRANK - FRESH FROM MACHINE SHOP OS Giken OS-88 solid direct shifter Ross tuffbond metal jacket harmonic balancer / damper Jim berry race clutch Link to comment Share on other sites More sharing options...
R.3.2.G.T.R Posted September 14, 2018 Share Posted September 14, 2018 os giken box comes with clutch? what sort of power was it handling? Link to comment Share on other sites More sharing options...
BK Posted September 14, 2018 Author Share Posted September 14, 2018 No clutch with box as I'm still using my ATS carbon triple. Had around 530kw at wheels through it. About 1500km old. Only throwing it out there for offers as if it does not sell it goes back in my 32. Just thinking about going back to a dog box and won't need giken if I go that way. Link to comment Share on other sites More sharing options...
R.3.2.G.T.R Posted September 14, 2018 Share Posted September 14, 2018 3 hours ago, BK said: No clutch with box as I'm still using my ATS carbon triple. Had around 530kw at wheels through it. About 1500km old. Only throwing it out there for offers as if it does not sell it goes back in my 32. Just thinking about going back to a dog box and won't need giken if I go that way. i'll be around that power level once engine build has finished, ill do more research and come back to you Link to comment Share on other sites More sharing options...
BK Posted September 15, 2018 Author Share Posted September 15, 2018 Ok there is a heap of interest in the OS giken 5 speed gearbox, I actually have 2 of these. Lets be clear - offers over $5500 . No 4k as this doesn't even cover gearset / input shaft. To get one of these going it is at least $6k in parts, as the gearset + input shaft cost is around $5k. Genuine Nissan selector forks / synchro rings / bearings and other unforseen parts depending on what you have to replace when it's down is $1k - $2k range. Then you need a good existing box for it to go in, not to mention labour costs on top of that if you are getting someone to do it for you. I am not in a hurry to sell one of these Giken boxes, but would let one go for the right price. If not go and build one yourself and find out the cost to get one running. Also have a stock R33 GTR box rebuilt and unused since rebuild. - SOLD Price drop - $1450 - SOLD Fully reconditioned and not used since. Can be supplied as push or pull setup. (currently push) Link to comment Share on other sites More sharing options...
BK Posted September 28, 2018 Author Share Posted September 28, 2018 RB26 Nitto oil pump - SOLD R32 starter motor - SOLD R32 GTR wheels - SOLD. First post will be constantly updated for parts availability - all price dropped ! Make an offer. Everything is negotiable and can ship anywhere. Link to comment Share on other sites More sharing options...
jet09s Posted October 1, 2018 Share Posted October 1, 2018 R32 gtr wheels sold to me Link to comment Share on other sites More sharing options...
BK Posted October 5, 2018 Author Share Posted October 5, 2018 Photos added to original post. More to come. Link to comment Share on other sites More sharing options...
BK Posted October 10, 2018 Author Share Posted October 10, 2018 New photos of rebuilt and reconditioned R33 GTR transmission. Now fitted with R32 GTR transfer case. Setup as push box. Link to comment Share on other sites More sharing options...
BK Posted October 13, 2018 Author Share Posted October 13, 2018 SPLITFIRE COILPACKS SOLD Link to comment Share on other sites More sharing options...
BK Posted October 16, 2018 Author Share Posted October 16, 2018 30 tooth R32 GTR rear diff half shafts, Nitto billet rods and CP pistons SOLD pending payment. Newly added to first post. R32 / R33 GTR 8 litre TRUST Greddy extended sump. Has extended pickup and baffle. Complete bolt on. $800 Link to comment Share on other sites More sharing options...
BakemonoRicer Posted October 16, 2018 Share Posted October 16, 2018 Pics of sump mate? Showing flange condition, and overall condition etc... Link to comment Share on other sites More sharing options...
BK Posted October 17, 2018 Author Share Posted October 17, 2018 Trust sump pics. Has fitting for head drain also. Freight is about $70 - $90 depending on location. Straight out of my R32. Going dry sump, so now not needed. Would put it on my R33 GTR if I could be bothered to pull engine out. Link to comment Share on other sites More sharing options...
BK Posted October 18, 2018 Author Share Posted October 18, 2018 30 tooth R32 GTR rear diff half shafts - SOLD Trust sump SOLD pending payment Link to comment Share on other sites More sharing options...
BK Posted October 19, 2018 Author Share Posted October 19, 2018 Trust RB26 sump - SOLD CP 86.5mm pistons - SOLD R32 GTR rear diff cover SOLD pending payment It's all going FAST ! Link to comment Share on other sites More sharing options...
BK Posted October 22, 2018 Author Share Posted October 22, 2018 R32 GTR rear diff cover - SOLD R32 GTR rear LSD diff centre - SOLD Link to comment Share on other sites More sharing options...
BK Posted October 23, 2018 Author Share Posted October 23, 2018 Nitto billet rods - SOLD R33 GTR gearbox - SOLD Link to comment Share on other sites More sharing options...
iruvyouskyrine Posted October 24, 2018 Share Posted October 24, 2018 Condition of oil cap? Link to comment Share on other sites More sharing options...
BK Posted October 24, 2018 Author Share Posted October 24, 2018 one scratch on top Link to comment Share on other sites More sharing options...
R32GOJIRA Posted October 25, 2018 Share Posted October 25, 2018 With the 31 spline half shafts, what else is needed to fit them to a pre 94 R32 GTR diff? I have a quaife centre that i eventually want to fit into my car. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now