Jump to content
SAU Community

Project 'Wheezy' Coupe


Recommended Posts

  • 5 months later...

Slow progress and a while between updates as I decided late last year to build a new house and move away from the city now that my wife and I no longer have a permanent working location.

Anyways, I fitted Bosch pressure/temp sensors for oil/fuel/water and a flex sensor too. Which means when I pull the finger out for the full beans tune I will get a flex tune rather than straight E85.

 

Finally got around to fitting my fixed back seat on the weekend just gone. (Need to re-fit the harness at some point)
Hopefully get out for a drive in the coming weekends once other commitments settle down and see if it was a good or bad decision.

PXL_20210515_042419524.jpg

PXL_20210515_042703187.jpg

  • Like 3
Link to comment
Share on other sites

Small sneaky update.
I was never happy with the Otaku Garage adapter plate for the RB26 intake. I had issues with it leaking, being generally very soft material and I ended up re coiling the threads.

 

A mate of a mate got onto Racefab in NZ who used to make what is essentially inspired/copies of the Blitz adapter plate from years ago.

Turns out he had two left on the shelf that were never sold.
So I managed after about a month of back and forth getting my hands on one.

I started stripping the intake off today and it should be on this weekend.
I hope this is the last time the intake needs to come off for a very long time!

PXL_20210521_010951452.jpg

PXL_20210524_051119405.jpg

  • Like 4
Link to comment
Share on other sites

  • 2 weeks later...

Got the car back together and will hopefully get a much needed alignment this weekend.
That is providing lock down in Melbourne lifts :(

Was looking at options for Wifi to the Emtron on Friday night and ended up buying a small wifi router for $34 delivered on Amazon.

 

Pretty cool little gadget and has already come in handy to look at the ECU logs etc without having to grab a wire and stuff around in the cabin.

Link to comment
Share on other sites

Made a sneaky patch loom for the Fuel Level Sender Conditioner today. It adapts into the loom which powers the dash so that I can give both the dash and the conditioner 12v.

The rest of the loom runs to the conditioner itself and a DTM-3P connector for power, earth and the signal from the fuel level sender itself (I will intercept the wire on the dash for the factory gauge).


The little wire dangling (I should have given it more length, but long story) will go to the input on the ECU.

PXL_20210608_064759854.jpg

  • Like 2
Link to comment
Share on other sites

  • 4 weeks later...
  • 2 months later...

So much bogan power!!!

In other news, still getting KMs on the car before all the boosts.
And am going to put a pressure/temp sensor on the hot side of the intercooler to measure pressure drop and temps pre intercooler.

Lastly, have a surprise coming around Jan for this which will change the look of the car quite significantly IMO :)

DSC_0006.JPG

DSC_0008.JPG

DSC_0005.JPG

DSC_0009.JPG

Edited by Wheezy
  • Like 1
Link to comment
Share on other sites

  • 3 months later...
  • 1 month later...
  • 4 months later...

So now it's winter and I'm in the middle of a move, not much will be happening for a few months.
My current list of tasks when it gets warmer and I settle into my new house.

Install Emtron Keypad & Program
Install Trigger Kit
Make & Install a 3.5" front/dump pipe (Stainless)
Install R31 House Rear Camber Kit
Install Dual Pumps & -8 Hard Lines
Replace damaged Dash Trims/Buttons
Restore Weather Trims
Obtain New Door Seals (aftermarket)

Link to comment
Share on other sites

  • 11 months later...

Moved house and am slowly knocking things off the list.

I found a set of close to brand new tail lights (used for 12 months on another HR31)
I had the OE CAS fail a few months ago so I installed my new trigger kit.

  • Install Emtron Keypad & Program
  • Install Trigger Kit
  • Obtain New Door Seals (aftermarket)


I'm currently building a shed at the new home, so once that is done I will be focusing on the fabrication side, IE:

  • Make & Install a 3.5" front/dump pipe (Stainless)
  • Install R31 House Rear Camber Kit (Will be paying a professional)
  • Install Dual Pumps & -8 Hard Lines


That leaves the aesthetic side:

  • Replace damaged Dash Trims/Buttons
  • Restore Weather Trims


I'd also like to give the paint side some love as its 14-15 years since it was painted.

PXL_20230403_065646421.jpg

PXL_20230403_065609696.jpg

PXL_20230417_012951142.jpg

PXL_20230417_012855610.jpg

PXL_20230508_015048885.jpg

PXL_20230417_012516973.jpg

PXL_20230424_102717515.jpg

  • Like 4
Link to comment
Share on other sites

On 6/18/2023 at 8:58 AM, Roy said:

Old cars are too much work. Time to sell up and buy weak ass M4 or something. I may know a buyer for the 31 :)

 

I'm still pulling pennies for an Emtron

You are #1 in my contact list if I was ever to sell :P

I'm torn between the Emtron dash and a new daily....Y62 with an exhaust would be nice if I hadn't doubled my mortgage debt :(

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




×
×
  • Create New...