Jump to content
SAU Community

Recommended Posts

Having issues with my rb20det. I'm struggling to even get it to crank. So far i've replaced the battery + starter, but when i go to try crank it struggles, similar to like what a dead battery would do

Checked the voltage on battery 13.4v, all the grounds are there. Is there something that could be draining the starter?

 

Link to comment
https://www.sau.com.au/forums/topic/480913-rb20-starting-help/
Share on other sites

"New" or "another" ie second hand?

(had a similar problem with my Pathfinder - got second hand starter, and it failed same way in four weeks!)

Does it start easier once you get it started and the engine warms up? What is the battery voltage when the engine is running?

Another thing that will cause this is a seized alternator, ac compressor or p/s pump. It will make the engine turn over much slower causing it not to start. 

I see this often on Suzuki's with seized alternators. 

Edited by TurboTapin

New, I managed to get a brand new forklift one that i've read people are running.

Doesn't start, just everytime i switch the ignition key, attempts to crank and then nothing. I'll see if i can find another alternator to try it with. 

 

I'm able to crank it by hand, and putting 12v directly to starter doesn't make any difference 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...