Jump to content
SAU Community

Carbon rb timing cover

Millerman
 Share

Recommended Posts

Millerman Collaborator

Millerman

Posted
Posted

Hey guys 

i recently purchased this as a bit of an impulse buy. I have an rb25 that im putting into my datsun and i thought this would be a cool addition. I didnt however realise that this is suited for an rb26...idiot! 
i know i can modify the engine and or the cover to make it work but id rather pass it on to the next person. 
the build quality is great! 
It does have a small defect on one mounting point but doesnt effect mounting! 
 

asking $50 

located Adelaide but happy to post

0407793620

thanks Dan

might swap for other rb25 things? Lemme know what you have! 
 


 

A5CDCD61-1C10-445D-9CFD-427FF0D193F4.jpeg

F392F723-AAA2-4EC4-A017-7D950D36366B.jpeg

CD922A8E-5E97-4DA1-A058-C6BF8C51E5CD.jpeg

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • portaz
      Walbro 460 in r32 gtr

      By portaz · Posted

      I disconnected before the fuel pump and restriction still there. Disconnected at turbosmart fpr and also after ethanol sensor and pressure dropped. No kinks in line but I found one spot above diff that I can hear the fuel flowing while running so I'm wondering if there is built up corrosion  from 10 years of sitting.  I had injectors cleaned and tested and one was dead but rest were fine. Was never an issue when I owned the car previously but I'll talk to jez about his thoughts on if they should be changed to newer tech. Thx guys at least I know the setup should work again. Pump is wired directly to relay and not using factory plug any  more 
    • robbo_rb180
      R32 Gts+t Daily/street

      By robbo_rb180 · Posted

      Nice work on the shroud/ducting.  
    • ELFGT350
      Newbies

      By ELFGT350 · Posted

      Hi and best of luck with your car. Its a bit hard to tell how low the car is all round from that pic or if its been lowered or not. 90mm is a bit low on the front apron but it depends on the shocks & springs condition & whether or not its been lowered. Going to 19” wheels will give you 15-20mm depending on rubber but you might need new shocks. Mine -2005 are weeping fluid slightly but have lasted 19years!!. So if yours are original they need replacing anyway if they havent been touched before.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Hi everyone, Recently got handed down a 2004 Skyline 350GT Coupe. I would like to change the wheels as the previous owner installed some weird ones. The current ones are 215/45ZR18, unsure of the offset, and sit pretty deep in. Would like to increase the ground clearance slightly as well as I need to get it roadworthy standard, currently sitting at 90mm. Was thinking that maybe I could kill 2 birds with 1 stone by getting new wheels.  Pictures of current wheels: https://imgur.com/bg1QMIu Any recommendations for the types of wheels I should be on the lookout for? Like the maximum and minimum offset, sidewall height, width, etc.  Sorry in advance if I'm noob, I do not know much about cars other than how to change the oil, a blown tyre and brakepads....
    • Lvonn1
      RB25DE Rebuild tolerances

      By Lvonn1 · Posted

      Hey MinKer, Where abouts did you get that table from ? 
×
×
  • Create New...