Jump to content
SAU Community

R34 gtr brembos on gtt rotors?


seriesII
 Share

Recommended Posts

Hi sorry if someone has asked this before..I had a search :(

 

Just wanted to know if front brembo r34 gtr calipers direct fit onto gtt rotors with no issues..

My r34 came with front gold brembos and looking to change the worn down slotted rotors that it came with though im not sure if they are gtt rotors or a little larger or thicker?..thanx 

Link to comment
Share on other sites

Thanks I better do that..was seeing if anyone knew before i jacked it up..  was thinking it must be thicker then a gtt rotor...  though does a larger rotor fit?..  it would only be the thickness difference? Not a height or width difference?..   when I spin the wheel it sounds like the rotor makes a small grind sound when I try spin it..is this normal? Or shouldit free spin with no small grind sound?   ..sux when you get a car and not sure what someone has done or if it's riggt 

Link to comment
Share on other sites

No. GT-T rotors are only 310mm diameter. GTR Brembo rotors are 324mm diameter. You cannot put a GTR Brembo on a 310mm rotor.

Just repetition for repetition's sake.

 

But.....GTR Brembo rotors aren't thicker. They're all 30mm. Only the 296mm GTR rotors are 32mm. Right?

Link to comment
Share on other sites

Haha Oh son of rajab . Its like that haha..I checked the pads and they are gtr bolt line up so few they are brembo gtr....I think i must be thicker as i measured and def past 310mm... came to past 320mm so must be 324mm..sorry to ask is the gtr r34 rotor different I size? Or is it just the thickness..should be right to get gtr r34 rotor it sounds? .thanx so much to all

Link to comment
Share on other sites

Are you sure they are R34 GTR calipers? It is very common to install Z33 front Brembo calipers but the rears don't fit.

If you have front a rear Brembos then they would most likely be R34  GTR ones. And the rotors are different between 

BNR34 and Z33.

Link to comment
Share on other sites

R32-R34 GTR 324mm rotors are all the same

The Z33 324mm rotors have a different hat height.

You'll need to measure this to work out what you have. Google how to measure rotor hat height and follow instructions.

 

 

 

 

  • Thanks 1
Link to comment
Share on other sites

Ahh I'll look...they are the nice gold brembo that the had did z33 have gold?...crZy so z33 calpiers bolt dorr direct into the front if a r34? The bolt pattern to take them on and off...  thanks all I'll measure the height and all and see what size... they seem to take r34 gtr pads though looked up and z33 seems to have the same front pad.. so may be z33 brembos..

Thanx for the help guys..didn't want to buy the wrong one and have my wheels on And of alot..

Link to comment
Share on other sites

On 18/12/2020 at 3:18 PM, Dose Pipe Sutututu said:

Yes, here's a guide I wrote back then when I cared about sharing knowledge lol

http://www.trak-life.com/diy-350z-brembo-brakes-conversion-nissan-skyline-r33-gts-t-gts-gts-4/

oh wow they do bolt into the same place and just a rotar change.. thank you for that.. seems it could be either brembo.. measure it is it seems. So I'll do that soon. Thanks to all who helped and cleared this up for me.. lol @ when I cared about sharing knowledge 🤣🤣 ..so gets like that 

Link to comment
Share on other sites

My dust pan is still on my fronts and has the lip sitll..does this mean mine are r34 brembos and gtr rotors? As my dust pan is not hiting my rotor and has the lip..?..  in this guide for z33 calpiers you need to trim the dust pan lip or remove it for z33 rotors 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Maybe I used the wrong sandwich plate as well. Used one piece instead of two piece.  
    • Y'know what, after reading a topic on a 360kw build using a nistune (who ended up going LINK), im now considering a LINK over a nistune. The engine protection alone would probably be worth it. And id like to learn to tune so would be nice to have that safe guard. Which means i probably wont need a boost controller then, or the R35 MAF.  Becoming a bit of a blog now but oh wells. As mentioned previously, the goal is around 300kw, for a daily driver. Will be looking at fitting a highflow turbo or similar (something that doesnt require downpipes, manifolds etc to be changed out) when the current stock gives out or the money for it is there. 
    • Thanks guys. Are you meant to tighten the converter bolts through the starter motor hole? Think my plate between gearbox and engine is one piece. Im heading up there tomorrow.
    • Picked my tailshaft up yesterday arv!! Test fit it and because they've gone to a ford centre bearing and CV I had to modify the mounting bracket a little bit. 5mm of each side and she went up into position and fits well. It has a 1350 uni and flange on the gearbox end so it should be plenty strong!  Got stuck in this morning and started on the wiring mess. Cut out all the wires not required that go to the body connector and cut the engine harness out. Need to go through and work out which ones I need to keep and rewire into the new ecu. Should save a small amount of weight as well. I'd love to get in and rip the dash and everything out to completely remove wiring but cbf.  Next up was the power harness for alternator, starter etc. It has a few connectors from factory that run out of it. Cut it all apart and removed what was no longer required and put some new corro and taped it all back up and bolted it all back into place.  After that I worked out where I can mount the new flex sensor. Found a couple of factory bolt holes and drilled a new hole on the bracket to suit. Need to go get a few fittings and adapters tomorrow so I can keep going.   
    • Nah, im after the more newer looking, one with the OLED display
×
×
  • Create New...