[Rb26 Water Pipes]

i didn't think it would be a problem but wanted to make sure

[Rb26 Water Pipes]

i have blocked these to water pipes off from going round the back of the block to the turbos

because i'm using a single turbo setup and using the water jacket from the block and the water pipe from the front to feed the turbo

but am just thinking if i should connect it to the water pipe at the front for coolant flow in the intake manifold ?????

[Rb26 Water Pipes]

i have blocked these to water pipes off from going round the back of the block to the turbos

because i'm using a single turbo setup and using the water jacket from the block and the water pipe from the front to feed the turbo

but am just thinking if i should connect it to the water pipe at the front for coolant flow in the intake manifold ?????

[R33 Starter Motor Rb Altinator Rb Tbelt Plate On Crank Rb Powersteering Pump]

as above correct me if i'm wrong but i think rb20 rb25 and rb26 altinators and powersteering pumps are the same

i also need the timming belt retaining plate that goes between harmonic balancer and crankshaft timming gear

[Rb20 Rb25 Rb26 Flywheel Backing Plate]

as above

i have a rb26 and i'm pritty sure the other rb engines use the same backing plates

[Having A Bit Of A Clean Out Found Some Bits I Dont Need]

turbo down to $300

[Having A Bit Of A Clean Out Found Some Bits I Dont Need]

pistons/rods sold

[Having A Bit Of A Clean Out Found Some Bits I Dont Need]

cooler sold

[180Xs Compliance With No Engine & Gearbox]

are you brissy based? if so I can probably help in a way.

whn you bough it was it registered at all or had it been through registration?

do you have a chassis number at all?

i'm in central qld

it hasn't been registered no aus vin number just the jap one

[Having A Bit Of A Clean Out Found Some Bits I Dont Need]

got some bits and pieces to get rid of i can organise postage or the buyer can if they get a cheaper rate

1 big turbo off a tractor of some sort a bit big for my plans but someone else might have some fun with it $500 ono

450mm x 300mm x 75mm hybrid intercooler never been used chineese i think $50

r32 rb26 conrods with pistons $50

r32 rb26 standard cams $20

r32 rb26 standard exhaust manifolds $20

clutch pedal off s13 i think the bolts were too short for mine dont know what happened there but can be modded $20

brake pedal off s13 $20

drivers side elec window assy $30

drivers side door handle $20

passneger side mirror $30

air orbital sander $30

sony cdx-ca730X $10

[Having A Bit Of A Clean Out Found Some Bits I Dont Need]

got some bits and pieces to get rid of i can organise postage or the buyer can if they get a cheaper rate

1 big turbo off a tractor of some sort a bit big for my plans but someone else might have some fun with it $500 ono

450mm x 300mm x 75mm hybrid intercooler never been used chineese i think $50

r32 rb26 conrods with pistons $50

r32 rb26 standard cams $20

r32 rb26 standard exhaust manifolds $20

clutch pedal off s13 i think the bolts were too short for mine dont know what happened there but can be modded $20

brake pedal off s13 $20

drivers side elec window assy $30

drivers side door handle $20

passneger side mirror $30

air orbital sander $30

sony cdx-ca730X $10

[Wtb Gtr Rods]

hi mate i got some r32 stock ones look to be ok

$50 plus postage if ya like

[180Xs Compliance With No Engine & Gearbox]

Some rules don't apply here !!!!

any rules that could help me out?

[180Xs Compliance With No Engine & Gearbox]

firstly i would say check ALL OVER THE CAR for a pink / green / purple plate etc etc.. check in the door jambs on the passenger door..

if it's still not there i would be inclined to say that no, you will definitely not be able to get that vehicle complied with an RB26. or possibly comply it at all...

that said - i see you're from queensland - and from what i see over there, it's pretty much anything goes if you slip em a XXXX!!!! ahahaha

LOL yer wish it was that easy

i looked every were its like some one half tried to comply it cos its got the side intrusion bars but just no paper work and no green plate

no wonder it was cheap

[180Xs Compliance With No Engine & Gearbox]

ok so i bought this 180 shell a while back and been planning a bit of a project

but i realised it's got no green plate and was wondering if i can still get one with a rb26 in her

i'd like to register it

[Rb26 With Rb25 Gear Box]

i plan on ordering a clutch online just wondering which one fits i plan on buying a lightened flywheel with the kit as well

[R32 Rb26 Into R32Gts-T Rb20 Wiring Harness]

thanx mate

i guess its not the quick fix i was hoping for ill see if i can hunt down a rb26 harness

[R32 Rb26 Into R32Gts-T Rb20 Wiring Harness]

thats the prob i dont have the 26 harness the block i got was fairly bare but it still has most of the sensors still on it

i plan on running a haltec or similar with map sensor ecu

i dont really wanna pay for a after market harness that why i was hoping the rb20 harness works

[R32 Rb26 Into R32Gts-T Rb20 Wiring Harness]

"bump"

[Lower Timming Belt Cover]

thanx ill pm ya

[Lower Timming Belt Cover]

hi i need the bottom timming belt cover please

[Rb26 Into S13 Sil With Rb25 Box]

as above but do i need to fabricate a gbox crossmember or is there a straight fit ?

[R32 Rb26 Into R32Gts-T Rb20 Wiring Harness]

anyone know if the sensors are different they seam the same

[R32 Rb26 Into R32Gts-T Rb20 Wiring Harness]

in the middle of doin a rb26 into r32 gts-t and wondering if i can use the rb20 wiring harness ill be running an after market computer with map sensor so the duel air flow

sensors wont be a problem

all the other sensor plugs look the same but just want to be sure

[Rb26 Into R32 Gts-T]

thanx for that

i gotta track some rb20 brackets now