jayo

i picked up some 350z wheels there 18"x8" with I believe a +35 or offset Front and Back car just needs to be a little bit lower.

so plans have changed with this, after driving it for a few months i have gotten lazy driving the auto, so i sold the gtr box. i picked up some new shoes for it this the weekend. they are 350z alloys and i think they look perfect on it. im just going to lower it a little and enjoy it. very comfy cruiser with plenty of go when needed

cheers lads few pics after a quick wash

i imported a grade 4 nissan stagea earlier in the year, i recently put it on the road. such a comfy cruiser with plenty of power!! its tiptronic at the minute with rb25det neo engine. i have been gathering the bits needed to convert it from 4wd auto to rwd manual. so far i have r32 gtr gearbox (can run 4wd / rwd with this box) exedy clutch nismo lightened flywheel clutch fork gtr slave cylinder gtst master cylinder r33 handbrake r33 manual centre console r33 pedals all i need to get now is manual spigot bearing r33 handbrake cables manual bellhousing bolts it has full leather interior, with front heated seats decent speakers factory hids plenty of boot space i have wheels on route from yahoo auction for it, should have them early in the new year. they are 18" x 8j +38 when i get conversion done and wheels on i will look at uping the power anyway heres a few pics of it as it stands such an under rated car!

looking for part numbers for the following rb25det flywheel bolts is it (12315-42L11) rb25det manual spigot bush rb25det manual gearbox bolts is it (01121-05121 x 3 long top bell housing 31377-15U00 x 3 bottom bell housing 31377-15U01 x 1 bottom bell housing, far left facing the front of the trans, outer bolt for the gusset support. 08911-2101A x 1 hex nut for the far left bolt.) r33 gtst handbrake cables thanks

ok thanks,im not 100% sure myself. i was under the impression it wasnt a straight swap over? if the 33,34 senders fit the gearbox ill just pick one of them up. i just started collecting parts for the conversion.i want to have all the right bits before i start.

Thanks kiwirs4t. I found a company in the UK that do A converter for r32 gtr box to convert It to electronic. Thanks

anyone know how to wire the gearbox up in the s2? what have people done with the speedo drive in the past?

im gathering all the bits to do a manual conversion on my s2. from what i can see the wiring seems to be different than s1 stagea's. can anyone point me in the right direction of what needs to be done?

im in the process of gathering all the bits to convert my s2 stagea to manual what needs to be done regarding wiring? most the info i can find is for s1 stagea's and i have seen that the wiring is different on s2. can any body point me in the right direction?

hi, im thinking of converting my s2 to manual few questions though. will an r32 gtr front prop shaft work?or do i need an r33 one? is there anything else that i need other than whats listed 33 gtst clutch pedal r33 gtst clutch master cylinder r33 gtst handbrake r32 gtr gearbox a push type r32 gtr clutch and flywheel r32 gtr clutch slave cylinder rb25 manual flywheel bolts rb25 manual spigot bush for the crank conceptua braided clutch line manual gearbox bolts

thats great,thanks. have a decat and will be getting custom cat back system made to fit. thanks

i have been looking at exhausts and cant figure out if an r32/r33 turbo elbow and down pipe will fit my stagea. its one complete unit turbo elbow and down pipe in one piece. can anyone tell me if it fits before i order it

Perfect. I'll pick up a cheap seat until I Find a decent gtr. Thanks

hi, any recommendations on what coilovers and spring rates to use in the stagea? are the meisterR Zeta-R 9kg front / 7kg rear any good?