moobaque
-
Posts
323 -
Joined
-
Last visited
-
Feedback
0%
Content Type
Profiles
Forums
Events
Gallery
Media Demo
Store
Posts posted by moobaque
-
-
Im having almost exactly the same issue. My problems started after the car sat idle for a few months while I was overseas.
At first it seemed like it would only occur when running up a hill, but not every hill, just say one in every 50 for example, but it seems like the problem has evolved as it now occurs on any or no incline. This also happens randomly at any speed, and/or anywhere in the rev range.
In the same way as cactus stated, when the car runs, it drives like a dream. But the cutting of power is completely random. Its pretty safe to say that the car will work fine for at least 10 minutes at the start of the day, but anywhere from 10-30mins of driving, at some stage the power will cut. It may just be for a second or two and then continue on, or like what happened on the freeway the other day. Driving at 100, power cut, never came back, rolled to the emergency lane.
Sometimes you can restart the car immediately and continue on your merry way, but what is happening more often now is you have to sit for a few minutes before it will restart. I have a power fc with hand controller, and there is nothing crazing going on when I watch the voltage readings from the AFM. There also no coughing or hesitation of the engine, so its not like the fuel pressure is simply dropping, its almost like the ignition gets cut. My water temp is sitting at around 70º normally, but its not like its spiking at the points of stalling.
The car has had its coilpacks replaced, new spark plugs, cleaned all ignition loom connections, AFM sensor and connector cleaned, fuel filter replaced and a new air filter for good measure. All of which has made zero difference. The car is running the standard fuel pump, but I do have a spare 040 kicking around that I will swap when I get the chance, but like I said it before the power loss is to instantaneous, seeming more like its on the electrical side of things.
I'm really hoping someone can shed some light on this as its becoming quite an inconvenience.
Cheers
-
Thanks guys, I did wonder when I was in the car the other day if it might also relate to the main braking system.
I tried pumping the brake to see if more pressure made any difference to the warning, but no dice.
The reservoir is below max but still within the indicated min mark. Will give a little bit of a top up and check out how the brake pads are fairing tomorrow. Certainly still have a firm pedal feel so hopefully its just being over sensitive to the reservoir level.
Thanks again and hopefully I'll have good news to report soon.
-
Hi All,
In the last couple of weeks and mainly since our cold Melbourne mornings I'm getting the hand brake dash light staying on in my R33.
Sometimes the light will turn off immediately after the hand brake is released then will turn on again after several seconds, but mostly it will remain on until the engine has been running for 10-15 minutes. For the rest of the day it will continue indicating correctly.
Now i'm wondering if this light might be used to indicate any other car related issues? I do have a power fc but as far as im aware it only uses the engine light for sensor maxing and the rest of the warning lights should act as they did with the OEM ECU.
The car doesn't appear to be driving any different than normal, and it may very well be just a faulting switch on the hand brake. But this starts to seem unlikely when as mentioned early sometimes it does go off as it should then turns on again (without touching the hand brake)
Any help would be very appreciated.
Thanks
-
Hey mate,
I'm after the drivers side interior a-pillar with clips.
Drivers-side door window glass
And driver side door frame rubber.
Cheers
Cam
-
Hey mate.
Do you have the front inner plastic guards that go between the wheels and front bar? (both sides)
Cheers
Cam
-
I'm tryin to ship my car down from Sydney To Melbourne
Does anyone know which companies are good to deal with?
Cheers.
I'm looking to do the same thing in Feb. Just got a quote of Autotrans.....$1400.... since it only cost me $100ish in fuel to do the drive up here, might find the time to fit in the drive back...
-
I simple check before your spend any money would be to remove your thermostat... chuck a pot of water on the stove... ideally if have a thermometer you can keep an eye on how hot the water is getting.. place the thermostat in the water and see if it opens.
-
I'm definitely green when it comes to fuel systems... so i'm just curious does everyone who chucks in a 040 NOT have some sort of filter on the end of it? like the oem or walbro? sounds like a very easy way to get shit stuck in your fuel lines... sure the fuel filter in the engine bay may stop it... but still there is alot of piping in between.
Cheers
Camden
-
I use to think my clutch was stock too (got the car at 60,000ks)... peddle was relatively light etc etc. That was until I jumped into my friends car and realized how much heavier my pressure plate really was. Still started to die at 180kw.... was destroyed once got 200+
-
Payment & PM Sent
-
If it ain't broke, don't fix it.
Except your talking about a stock rb25 turbo that are prone to disintegrating when boost is above standard (he states he is running at 12psi)
Our stupid turbines are ceramic bonded to steal....
Here are a couple options.
GCG rebuilt with Garrett components (about $2000) chasers motorworks also offer a similar service
HKS GT-RS kit. (about $3500 imported from japan or add another 1k or so if you buy locally)
and thats about where it ends before your looking at new manifold, dump pipe, etc.
Cheers
Camden
-
I don't think there is necessarily a golden rule. It's all about how the peddle feels. Environmental factors as well as how hard you brake on the track will determine how long it lasts. If the the peddle ain't solid anymore... New fluid time.
With my track abilities (hah which ain't that amazing) every couple of track days is so fine. But if its just street driving well over a year should be fine even with cheap fluid.
Cheers
Cam
-
i have the justjap return flow and as the others, had to cut the reo.
i dont really see you being able to get away with a front mount without having to cut the reo.
if you want to make sure you can return it to standard, buy a spare reo from a wrecking line and save it for when its needed.
You don't have to cut the whole cross member of the reo! although it will allow for much better airflow to your cooler.
You do how ever have to notch out a section at each end of your reo (basically where the end tanks are) the curvature of the reo is to harsh and will hit your end tanks before reaching the mount points. (Speaking from a Series 1 r33 point of view)
If you really don't want to touch a thing on your reo then the blitz is not going to work.. As already mentioned the ARC will but i don't think its actually made anymore?!?! and justjap sell a cheapy which im sure is perfectly fine unless your chasing mega power.
Cheers
Camden
-
just say if i buy a set of wheels with the same size but different offset,will the tyre still fit???
Sure will.
the physical width of the rim isn't changing, just its position in relation to mounting to the hub.
Cheers
Camden
-
Don't suppose your turbo had been hi flowed?
-
-
Typically you remove the whole boost controller as it is a bastard piece of shit really. (Although mine is still bolted to the firewall, it really is crap, and is disconnected)
Your post doesn't really make any sense... Are you just trying to make the point that an ebc is better than a bleed valve (clearly this is true so not very helpful)
Or do you think we are talking about the stock boost solenoid?!? the stock solenoid is redundant with the bleed valve or an ebc for that matter and is bypassed...
Cheers
Camden
-
Turbo smart bleed valve has a TPiece in it correct?
If it does, openit, remove the ball and spring, put it back together. (WITHOUT THE BALL AND SPRING)
This thing holds the waste gate open.
Had the same Boost Controller, had the EXACT same issue.
Certainly worth trying! I never thought of removing it as i was under the impression you only removed it if your boost was spiking.
Cheers
Camden
-
not going to doubt Ray as i know they do great work, but maybe talk to him about retarding the exhaust cam gear 2degrees(suggesting from other threads i have read, it is meant to help response) and pre boost timing, might be able to run more?
Yeah I'll definitely talk to Ray about it when i get back to Melb and get him to do a bit of a retune. Maybe go down the ebc path to at the same time and see what he can do with it.
This really has been something that the car has been doing for a long time but was less obvious up until recently as my clutch was progressively dieing. I now have a much more serious clutch (certainly no slippage anymore).
Cheers
Camden
-
If the bov is working properly, then maybe you have an ignition problem...
There is no obvious missing and when i changed the plugs and at that time i looked to see if there was any arching happening with the coil packs before putting the garnish back on and everything seems alright.
Another thing, that has happened in the past, is the adjustable cam gear on tight?cam gear is torque to what was specified on the paperwork but its not something that happened after putting it on anyway... was like this before.
Cheers
Camden
-
is your blow off valve set up and working properly. and also is the injector time delay set up properly ? cant remember propper word for it but it is why subarus feel laggy when you put a front mount on them . maf sees more air so puts in more fuel . extra air hasnt reached motor yet but xtra fuel has so rich flat spot then clears .
what is your boost gauge doing right after a shift ?
The blow off valve is standard and plumped back as it should be (and appears to be functioning correctly)
As for injector delay I am not sure but would be hoping this should be looked after correctly by my tuner (of whom i trust) although the car does run quite rich as demonstrated all over my rear bar.
I cant tell you exactly about how the boost gauge responds atm as im out of town (back home in a week) but from memory on shift and peddle down it jumps straight back up to something just over 0... maybe about 5psi!? sits there for that few seconds then builds its way to 12 relatively quickly. (like i said will be able to explain better next week when get home and give it a drive)
Cheers
Camden
-
Hey all,
My r33 gtst is putting out about 210kw with a selection of basic bolt on goodies. My goal isn't to make big numbers but I do want usable power. So having said that here is my issue.
As it seems at the moment 1st pulls quite well but shifting up into any gear even from redline has some serious lag. I don't appear to get any power back for 2-3 seconds in the next gear but then it kicks. This doesn't feel like a fuel supply issue nor does it miss or splutter (but i will be putting something like a 040 in soon anyway). (injectors are getting high on there duty cycle but certainly not maxing). Spark plugs are also new gapped at .8 (coppers)
So this is what the car has.
3" inch turbo back stainless steal exhaust with hiflow cat
apexi pod filter
turbo smart bleed valve (peaking at 12psi)
blitz front mount (this is no doubt not helping the lag issue at my current power)
apexi powerfc (tuned by re customs)
adjustable exhaust gear (currently at 0 degrees)
I'm assuming having just a bleed valve it may be allowing the wastegate to be opening early. But would it be that bad that an ebc would make all the difference? i don't know but i am assuming not.
I will also be looking at getting the standard turbo hi flowed mainly so the 13yo turbo doesn't disintegrate into my engine...but will the hi flow allow a faster spool up or should I be looking to spend more cash on gt-rs or similar? (a bolt on option is much more preferable than having to get custom piping / manifold made)
The car hasn't been tuned since we did the 100,000k service to it (and this is when the adjustable cam gear went on) So not sure if much if any benefit will come out of that at this stage.
anyway just looking for suggestions on what road i should be going down. I don't have a large wallet and i reiterate im not after big power figures just for the power to come on more linear.
Cheers
Camden
-
After a stock rb25det turbo that has been hi flowed...
-
Hey mate,
I'm looking to get myself some track rims at the moment. Just got to look into if the offset is going to work for me (r33gtst). Are you interested in selling them as rims only? I have no need for the tyres as i'll be putting semi's on anyway.
Cheers
Camden
Random Stalling
in Forced Induction Performance
Posted
So it seems like my issue has been solved by replacing the AFM! Its only been a few days, but not a single hesitation or stall since. The throttle is also noticeably more responsive at low Rpm.