Jump to content
SAU Community

BIGBOSS

Members
  • Posts

    364
  • Joined

  • Last visited

  • Feedback

    100%

Posts posted by BIGBOSS

  1. Hi all,

    I have a few bitz from a Rb25det race engine that i never completed & it has since

    been laying around my shed for a while.

    I need to move them on.

    List is as follows,

    1- Rb25det Stage 2 Race head.

    I have had this built by a professional shop and it is still brand new wrapped up in plastic.

    Head is off a series 2 R33 Gts-t & suits any Rb25det bottom end.

    Chemical clean

    Preasure & crack tested

    K-line guides,multi angle valve job

    Replaced super tech seals

    High lift spring & retainer kit with 9.5mm lift caability

    260cfm Race port for maximium flow.

    Included in the price is a pair of Tomei Poncams.

    Inlet is 256mm with 8.5mm lift

    Exhaust is 264mm with 8.5mm lift

    Also included in the packege is an adjustable Hks cam gear.

    With this Poncam set up you can still retain the factory VCT which is worth using as it will help with boost coming on around 500rpm earlier.The Poncams will give you greater low to mid range torque.

    This head is brand new,the Tomei cams and Hks cam gear have done around 1,200klms in a previous set up,& are in as new condition.

    Complete head set up with Cams & adj cam gear $2600

    2-Rb25det Stroker bottom end 2.7l.

    *Components have been in workshop sitting around & has some surface rust on Block,

    small amount on crank and some surface rust on the rods (as pictured)

    The block is Rb25det that has been mechined to 87mm

    The block was originally mechined at Jack bros Racing in Slacks creek along with the Rb26 Gtr crank & girdle.

    Pistons are JE from memory..87mm. New Total rings were fitted.

    Rods are Crower.

    After a small engine falure on the dyno (bearings) the bottom end was then stripped

    down and re machined by JHH Racing where it has since been sitting around in my shed in its current unassembled state.

    Odviously you will need to freshen up the bits again.

    Whole bottom end,Block,pistons,rods,Gtr crank & matching Gurdle $650

    3-Rb25det cranks & girdle.These were extracted from 2 good engines but didnt end up

    getting used.They will need a freshen up as have some surface rust on them

    $150 each

    4- This set up came out of a running Rb25det

    R33 Gtr injectors in Rb25det fuel rail with harness

    R33 Gtr injector resistor pack

    Z32 airflow meter

    Dont want to seperate at this stage

    Complete upgrade kit $350

    5-Ross Tuffbond metal jacket harmonic balancer Rb25det.Part number 306201.

    Rated to 1500hp

    Has done around 1,200klms and is still like new.I paid $750 for it.

    Sell $300

    6-Nismo Rb25det Engine mounts (left & right). Again done around 1,200klms & comes

    with the factory alloy bracks,Mounts are like new $230 pair

    7-R33 Gts-t dash cluster. Showing 82,000klms $120

    8-Rb25det starter motor $60

    9-Rb25 valley cover $30

    Rb25 rocker cover (oil cap side) powder coated blk $30

    Rb25 timing cover $10

    Im located on Brisbane southside.

    Pick up welcome

    For interstate buyers i can post or help with organising a courier for you at your

    cost.

    Please give me a call to make a time to view or if you have any questions.

    0424-380-848

    Cheers!

    post-70521-0-35167800-1428901248_thumb.jpg

    post-70521-0-83269300-1428901365_thumb.jpg

    post-70521-0-81012600-1428901396_thumb.jpg

    post-70521-0-83243500-1428901417_thumb.jpg

    post-70521-0-21583400-1428901441_thumb.jpg

    post-70521-0-48199500-1428901469_thumb.jpg

    post-70521-0-65298900-1428901493_thumb.jpg

    post-70521-0-15625400-1428901634_thumb.jpg

    post-70521-0-94652400-1428901653_thumb.jpg

    post-70521-0-96593800-1428901684_thumb.jpg

    post-70521-0-88565400-1428901820_thumb.jpg

    post-70521-0-17264300-1428901965_thumb.jpg

    post-70521-0-06681800-1428902025_thumb.jpg

    post-70521-0-21257200-1428902096_thumb.jpg

    post-70521-0-24480200-1428902171_thumb.jpg

    post-70521-0-69400700-1428902228_thumb.jpg

    post-70521-0-91933500-1428902487_thumb.jpg

    post-70521-0-26742100-1428902515_thumb.jpg

    post-70521-0-36658900-1428902547_thumb.jpg

    post-70521-0-62919100-1428902915_thumb.jpg

    • Like 1
  2. Hey all,

    I have a full set of R33 Gtr factory Brembos (front and rear caliper's)

    Ferodo ds2500 pads, front & rear.

    Full set of Adr approved brake lines, front & rear.

    A pair of front Japanese dixel slotted rotors (standard R33 Gtr 330mm)

    Brembos were off my 97 V-spec.

    The lines were made up from a brake shop here in Brisbane

    Pads were bought locally (Option 1 garage)

    The Brembos have had a seal kit put through them 12 months ago and have since done around 5000klms.

    The rotors have jst been machined.

    Everything is in excellent condition & I only pulled them off as have gone to a larger set up.

    Great upgrade for anything if u need to stop fast.

    The whole lot ready to bolt on $1700

    Im located on Southside of Brisbane and pick up welcome.

    For interstate buyers, im happy to help organise post or courier at your cost.

    These are packed up in a box & ready for a new home!

    For a quick response 0424-380-848

    Cheers!

    post-70521-0-71453600-1428784858_thumb.jpg

    post-70521-0-25113700-1428784881_thumb.jpg

    post-70521-0-31771000-1428784901_thumb.jpg

    post-70521-0-97481100-1428784934_thumb.jpg

    post-70521-0-31564500-1428784956_thumb.jpg

  3. It had a hybrid freak in it,Rb25 bottom end with Gtr crank. The head was an rb25 with twin trust t517z 8cm hanging off it.

    Made 550 atw with a Garage 13 ecu in it.I changed it to the pwr fc.

    It was built in Japan by Garage 13.The previous Japanese owner of it went out and got himself the cleanest/low klm R33 Gts-t he could find and modified it.

    The whole car is like new.

×
×
  • Create New...