[R33 Stuff To Clear Out Coilovers, Wheels, Diff, Seat, Steering Wheel Etc.]

What ratio is the diff?

[Rb30et Forged Pistons And Steel Head Gasket $1000ono]

Do you have pictures and part numbers?

[Wat Oil Pump Should I Use On My Twin Turbo 26/30]

if you go the nitto just remember they are set up to run high oil persure i just had to pull my sump of to lower the persure

HI,

What oil pressure did you have and what did you drop it to?

My N1 pump is putting out 8 bar (120psi) at 3000rpm.

I will have to reduce pressure as well.

[R33 Series 2 Abs Diff]

Hi guys i have a r33 series 2 abs diff everthing in good nick it has 4.11 gears after $250 for it

Hi Tony,

How many K,s has the diff done?

Stan

[Best Pistons Choice ?]

For your application, the piston to bore clearance should be 0.0025in - 0.003in including the coating so basically if you measure the skirt diameter inc the coating you should come up at 0.0025in piston to bore clearance measured half way down the skirt.

How are you measuring the clearance? How accurate is your equipment?

They are suitable for street use and will be slightly noisier than regular pistons but only very slightly. They shouldn't be extremely loud compared to stock but you will still hear them when the engine is cold. Mahle require tighter clearance compare to other manufacturers so possibly your machinist has set them half a thou over. But even then I wouldn't imagine it would be as loud as you are suggesting. (How loud exactly?)

Pedestrians looking when you drive past Loud. My machinist has heard the noise and agrees that it is piston noise.

As loud as stuffed lifters. The noise is VERY loud when cold and only a bit quieter when fully warmed up.

The equipment is machine shop equipment.

Measurement taken 10mm from the bottom of the skirt. I will check the measurement half way up the skirt tomorrow.

I am trying to decide if I should fit new pistons with longer skirts or maybe get another RB block and rebore it with tighter clearances

[Best Pistons Choice ?]

Another mahle user here

Here's a pic (note they're rb30 for 8.5CR)

Do you know the piston to bore clearance?

I have just fitted a rebuilt RB30/25 with Mahle pistons and the motor has very loud piston noise.

After 100klms with no change in the noise, I have pulled my motor out again and rechecked the clearances

and found them to be at .003" as my machinist had set them.

I have since heard that the pistons are race only pistons and not street suitable, that they are always noisy

and should have less clearance.

Do you know if this is correct?

[New R33 Hicas Boss Kit (made In Japan)]

As the title says, I have just bought a boss kit for my Momo Evo Millenium Steering wheel only to find my 33 doesn't have Hicas, so if anyone out there has a non-hicas boss sitting around new or used, I would be happy to swap.

Cheers

Matt

0413023669

Hi Matt,

I'm in the market for a steering wheel boss for a hicas R33 GTS.

How much do youy want for yours?

Sorry I don't have anything to swap.

thanks

Stan

[R34 Neo Transmission On R33 Rb25?]

Why do you want to put a r34 box in it?

Works out cheaper to put the 33 box in doesn't it? And push type clutches are cheaper....

I just got my car back from a manual conversion So just curious

P.S help me out here: http://www.skylinesaustralia.com/forums/in...howtopic=154422

I got an R34 box as it was all I could find at the time.

Push type is cheaper.

For your conversion you need the wiring harness from the gearbox up to the fuse/relay box on the drivers side inner guard for the reverse lights to operate.

For the speedo to work you need the manual speedo gear drive in the box and a manual speedo head or it may be easier to buy a complete cluster second hand.

Dont ask me why Nissan have a manual and auto speedo head, but they do.

Hope that helps.

Stan

[R34 Neo Transmission On R33 Rb25?]

anyone know if it would work vice versa, say r33 gbox into an r34 rb25det ?

thanks

Yes it does if you use the R33 gear lever, push type clutch and slave cylinder.

[R34 Neo Transmission On R33 Rb25?]

so has this been done before? does it fit straight on without any mods (apart from the flywheel/ can R33 flywheel fit?) or is there more to it and if there is plz explain

as T04GTR said, all you need is the gear lever and pull type clutch.

everything else bolts straight up.

[R34 Neo Transmission On R33 Rb25?]

i'm also intrested... ^^^

Yes you can.

Make sure you get the flywheel machined.

Even if the surface looks OK it is often dished slightly from heavy use.

[R34 Neo Transmission On R33 Rb25?]

yes it will.

youl need the shifter and a pull clutch/flywheel asembly.

either.

r33gtr or r34gtt. 250mm clutch

i had one in my dr30. nice box with good ratios and very smoth operation.

I am about to fit an R34 box into my 33GTSt. (Auto to manual conversion)

Can I use an R33 GTR flywheel with a pull type clutch?

[Mines Dumps, Bilsteins, Wolf 3d]

The Mines Dump Pipes have been sold.

Thankyou.

Stan.

[Rb Parts, Wheels, Heaps Of Other Parts]

Impul - the Rays nuts are black

Stan - I've got both, will PM you

Black32 - I'll have a look, will have to open a few diffs to check.

driftking - yes they fit on an S2 GTS-t

I wish to purchase these parts.

I'm still waiting for you to PM me

Thanks

Stan

[Wreaking R33 Gts-t & R34 Bits]

Hi,

I need a gearbox and allparts required to convert from auto to manual.

Can you supply them and how much?

Thanks

Stan

[email protected]

[Mines Dumps, Bilsteins, Wolf 3d]

Bilstein Shocks have been sold

Thanks

Stan

[Rb Parts, Wheels, Heaps Of Other Parts]

Hi,

I'm chasing the metal intercooler pipe between the Twin Turbo pipe and the Intercooler on the passenger side and an R33 metal power steering resevoir.

Can you help?

Thanks

Stan

[Gtr Turbos Plus Other Bits]

Hi,

Do you have for sale the metal pipe on the passenger side between the Twin turbo pipe and the intercooler?

I'm also chasing an R33 metal power steering resevoir.

Thanks

Stan

[Gtr Parts For Sale]

Hi Sasha,

I need the metal intercooler pipe and bracket on the passenger side that goes between the rubber hoses connecting the Twin Turbo pipe to the intercooler.

I also need a metal bodied R33 GTR power steering resevoir. (bolts to the left shock tower)

Can you help?

Stan

[email protected]

[Gtr Parts]

Hi,

I need the metal intercooler pipe between the Twin Turbo pipe and the intercooler on the passengers side.

Can you help?

Thanks

Stan

[Mines Dumps, Bilsteins, Wolf 3d]

WOLF 3D V4 has been SOLD

Thanks

Stan

[Mines Dumps, Bilsteins, Wolf 3d]

can u tell me which model it is

<{POST_SNAPBACK}>

Wolf3DV4 Plugin I should have put that in the description.

[Mines Dumps, Bilsteins, Wolf 3d]

can this wolf be used on a maunal im guessing yes and do u have the adaptors to go to a laptop or handcontroller

<{POST_SNAPBACK}>

It is best with a manual. It suits R32 RB20DET and R33 RB25DET. It connects directly to the factory wiring harness (Plugin) located behind the kick panel in the passenger side footwell.

The cable in the top of the picture is the adaptor for the com port on your laptop.

Hope this helps.

[Mines Dumps, Bilsteins, Wolf 3d]

Mines dump pipes -R32 GTR with O2 sensors

Second hand - Good condition

I purchased these to go on my Skyline, but now they are not needed as I bought a Twin Turbo and Dump pipe kit

$420.00 including postage

DUMP PIPES SOLD

Bilstein Shocks - R33 GTS25t

Like new. Only done 2500kms.

A bit too firm for the second rate back roads I spend most of my time on. Excellent on the highway.

$1000.00 including postage

SHOCKS SOLD

Wolf 3D V4 Plugin - R33GTS25t

Like new - was working well when removed from vehicle

It dosen't send the signals the auto requires for smooth shifts and factory type shift points. Outright performance was very good.

$780.00 Including postage

WOLF is SOLD

Thanks for looking.

Stan.

[email protected]

0414531156

[Gtr Intercooler Piping]

Searching for R33 GTR parts

1. Twin turbo pipe to intercooler piping

2. Intake Plenum to intercooler piping

3. Metal power steering resevoir

Thanks

Stan

[email protected]