big33r

As the topic suggest, I am looking to sell my R33 GTR V-SPEC. I've owned it for about 3 years with the initial intention of keeping it stock and enjoying the power . THEN i stopped being a girly man and built one amazing GTR. ​Privately built by a GTR mechanic then sent off to Jim at Dart Automotive, the car is no HP hero as Jim stated after a tune, but bring it back to me if you lose a race he said...... haven't seen him since ! Just a couple of Parts to name a few. - CP Pistons , Eagle Rods , - Prepped Block, tested, washed, R34 GTR crank - Oil restrictor - N1 Oil Pump with Billet Gears - Reconditioned head with Tomei Valve Springs, retainers, valves and Type B Cams - Garrett T04Z-R Dual Ball bearing with 1.00 Rear Housing, sits on a X-force hi mount Manifold with a Turbo Smart Hyper-Gate and Screamer Pipe - But what about the rb26 Oil issues ? BOOM Trust Extended Sump with Pick up (thanks Fatz) - Apexi Undercover Intercooler - Catch Can - Greddy Fuel rail, Sard 800cc Injectors, 1 Intank 044 Bosch Pump, 2 Mounted underneath the car - Buddy Club Coil overs with AME Tracers 18x11 rear and 18x10.5 front. Stance So much more but like i said this is an expression of interest . Wont let me upload photos so Text me on 0403 717 212 for Photos . Entertaining offers around the $32k Mark Located in Sydney

Anyone know how these would sit on an r33 gtr ? Looks tough

Cheers bud, shes a tough cookie

Bump for a tough 200sx

Amazing 200sx with not a dollar to sepnd. Nothing to hide on this built motor, all inspections welcome. This is what i mean by not a dollar to spend .... Head: Chemically cleaned, x-rayed, ported and polished Tomei 280 degree inlet and exhaust cams Tomei adjustable cam gears Tomei oversized valves Tomei valve springs Tomei retainers Tomei valve guides Tomei Solid lifter conversion Tomei rocker arm stoppers Nitto multi layer head gasket Arp Head stud kit Bottom end: Chemically cleaned, machined, x-rayed and full balanced bottom end JE forged lightweight pistons Eagle forged H beam conrods ACL race series big end bearings ACL race series main bearing ARP main stud conversion Engine externals: 850cc twin spray sard injectors Stainless exhaust manifold Garret GT35-66R ball bearing turbo Tial 38mm external wastegate Custom 3" stainless exhaust Greddy type S BOV Greddy oversize oil sump HKS oil filter relocation and cooler kit Braided lines and fittings SX Fuel pressure regulator with Oil catch can Very aggressive lumpy idle that rocks the car but is not too loud Black Plazmaman Pro Series FMIC 3'' heat coated piping. R33 5 Speed gearbox with machined synchros for quick smooth gear change OS Giken twin plate clutch R33 diff and drive shafts Balanced tailshaft HKS coilovers, height, damper and camber adjustable Endless 6 pot caliper brake upgrade still allowing the stock rims to fit Slotted rotors Adjustable suspension arms Haltec Platinum ECU, 4 bar map sensor Eboost 2 boost controller A/C is ice cold All power optioned $26500 ONO Located in Sydney PM me for more details Cheers Kris

Bump

Sorry $1750 to buy but would like a trade so my car isn't wheel-less

Hey guys, Currently running Enkei RPF01 wheels ,18 x 9.5 inches wide with a +15 offset on my GTR. Looking for a possible swap with cash difference either way. Running Falken Azinni Semi-Slick tires all round with tread . Great wheels , just bored . Let me know what you have . Located in Sydney Cheers Kris

bump

bump

sold

From what the previous owner told me they were new on the car he purchased and only did around 3000km, run at no more then 16psi due to a standard fuel setup .

bump

Bump ..

Bump

Hey Guys , 1. Have a set of Garrett -10 turbos, (HKS GTRS EQUIVALENT ) , the rears have been heat coated black, along with heat coated Ported manifolds and also aftermarket dump pipes. These were purchased off another member but never run on my car as a good deal on a single came past . From what ive read, these seem to make some good power and spin freely. $1500 for the lot 2. I also have a pair of unknown brand rear pods purchased off the forum in the midnight purple colour. They are fiberglass and I think they suit R33 gtr/gtst, they have been repaired and sprayed white, no damage and were only put against the car to see what they look like. It didnt fancy me too much so im selling them. Cost me $300 to repair and Respray on top of $250 for the pods. $400 Im located in Sydney , in the inner west region. Can post items at buyers expense if needed. Shoot us a text on 0403 717 212 or PM me. Have pictures of pods but not of turbos yet, can text pictures if needed Cheers Kris

Bump

Hey guys, Have a decent set of wheels for sale . Sat very nice on my R33 GTR but required spacers to clear the brakes. They have not one bit of gutter rash and were always kept clean. The tyres are all 90%+ all round and are kuhmos and falken Chasing 1500 ono , the tyres alone cost that . Located in Sydney Kris 0403 717 212

Hey bud, they are 17 inch. Make an offer

Thanks guys, will get the stethoscope out and have a listen !

Hey guys, Have just had fresh rebuild about 1500 km old , replaced nearly everything, eg eagle rods, cp pistons, acl race bearing, new crank, extended sump, n1 oil pump and nave noticed a ticking in the engine on idle that goes away after revving past 2500 rpm and nearly disappears when the engine is warm. When the car is cold , the ticking stays with the revs until about 2500 revs and then cant be heard. What do you experts think it could be? I hope its not a bearing on the way so soon but ive heard 2 of them before and it sounds different. Any help would be much appreciated!

BUMP

BUMPITY

Bump

bUmp