Jump to content
SAU Community

****************silvia S13 K ***************


Recommended Posts

post-24568-1143601790.jpg

SILVIA K 1990 CA18DET

rego till September

SYDNEY WEST

PRICE = 7.8k ONO

*ENGINE*

-98, 000kms

-auto

-CA18DET-urbo

-Hybrid fmic

-K&N pod

-gfb boost controller

-custom turbo back xhaust

-catch can

-nismo front and rear strut bars

-turbo smart bov

*INTERIOR*

-$1000 alarm system, remote start, inbuilt turbo timer, safty lock etc.

-clean stock

-boos steering wheel and kit

-jvc deck, 2 x 10" autobahn subz custom boot job black vinayl with piooneer 760 watt amp.

*EXTERIOR*

-Black body

-lowered on kigns

-Kspeed 17" bronze race rimz

-Lightly tinted windows

*OTHER*

- BN front bar ready for paint

- jrc front coilovers and tien rear lowred springs

- all stock parts, wing, piping, sterring wheel etc

- spare fmic cooler

- tanabe xausht muffler

- 4 x spare bov's

other commets: great reliable car, no problems ever and have all receipts of work done by ND mechanics in yennora. Serviced every 5000k's and im the seccond owner sicne landing in Aus in 2000. body may need a bit patching up but nothing serious just minor dents and scratches. welcome to inspect.

REASON for selling: just bought a civic and wanna work on it.

Contact: 0422 321 411 or msn [email protected]

pics:

post-24568-1143032341.jpgpost-24568-1143032472.jpg

will have more pics up soon just ask :P

Edited by slk1
Link to comment
https://www.sau.com.au/forums/topic/110758-silvia-s13-k/
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...