Jump to content
SAU Community

Recommended Posts

ive checked spark, took the coil pack out and earthed it on the engine through a screw driver (the professional way hahaha)

ill test the injector and resistor tomorrow when i can, im really leaning towards one of the injectors or resistors shitting themselves....

lol @ r31, really leaning towards a shitter to drive everytime my car dies!

Rb26 would be worth more than the car lol

ill get another rb20 and run 28psi lol

slide fly down and fix it for me, ill give you steaks..... :whistling:

Ordered new resistors so should be coming today, cant fix it today so have to leave it here another night... lucky its safe! tomorrow is D day!

the injectors and resistors came in and out 6times, due to 68ohm resistors instead of 6.8 so i dont think that i woulda done a 110% job putting them in the last time! having the shits and all......

the loud clanging, metal noise was scaring the sheet out of me last night, but i figured out that since it was running so rough it was ossicilating down the exhaust and it was shaking on the mounts PHEW!

I should have come down for those steaks

The water tasted funny in S.A lol

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...