Jump to content
SAU Community

$19k !! 1995 R33 gtst (perth) 12 second 'sleeper' with NOS

rev210
 Share

Recommended Posts

rev210 Grand Master

rev210

Posted
Posted

New lower price due to the fact that I'd actually have to pay capital gains tax if I get more money.

Don't wait around for this one!

1995 '12 second' R33 GTST 'sleeper' with NOS (Perth W.A)

Well it's that time of the year..

Time to sell the car and get a new one, for tax reasons as it is a work vehicle.

Totally stock looking manual 'silver' gtst with factory rims. A blank canvas to customise or leave as is to avoid unwanted attention.

CONDITION:

102,000kms regular servicing including transmission and diff.

Presently the car has a crease in the rear bumper and a few minor scratches, which will cost about $500-600 to clean up properly and the price reflects this. Interior is good. and it has a factory 7disc CD stacker/tuner and drivers airbag.

MODS.

* K&N Airfilter and modified airbox

* HKS exhaust cam gear

* Ogura Racing Chrome Molly flywheel

* 9 puck ceramic compound clutch

* FGK Super Ti cat back exhaust (very quiet and flows well)

* Custom Stainless steel turbo dump pipe and front pipe, with thermal wrapping.

* Apexi Super AFC II and sought after 95' ecu

* Peltier cooler on standard intercooler.

* Whiteline KCA349 diff cradle kit.

* Bosch Motorsport in tank fuel pump

* NOS EFI Nitrous kit (hidden underbonet) with 10lb bottle and 50hp jet. New nitrous solenoid.

The last outing saw the car run 13.3 and has since had a major tuning issue resolved which will has it making easy 12 second power. With larger decent rear tyres fitted 12's will not be a problem without NOS. The NOS activation offers the potential for low 12's and with the simple fittment of the 100hp jet an 11second pass.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...