Jump to content
SAU Community

Recommended Posts

For sale:

SSR Professor SP1 in Custom Type-C Bronze (Only set Worldwide done in Bronze!!!!)

19x9.5INCH +18 Fronts

19x11INCH +11 Rears

VERY NICE DISH on both.

Item Condition: LESS Than 6 months old. perfect nick, no scratches, no dings, gutter rash, all straight!

Price and price conditions:

$4200 OR NEAR Offer

Extra Info: Selling because, this did not clear my big supra brakes, so this is for Supras with smaller brakes, or Chaser, Aristo, RX7, RX8, Skyline, 200sx etc etc. Be the only one in the world to own the rarest custom SSR Type-C Bronze coloured Professor SP1's!!!!!! These were over $6000 NEW with tyres and 3 Months wait!

Pictures:

IMG_3233.jpg

FRONTS

IMG_3230.jpg

IMG_3227.jpg

IMG_3228.jpg

REARS

IMG_3232.jpg

IMG_3231.jpg

IMG_3229.jpg

HERE IS HOW THEY SIT ON MY CAR, Note the front was with a 22mm Spacer to clear the big brakes.

3183684019_f6183b4939_b.jpg

Rear fitted:

3183682583_6f380a16fa_b.jpg

3183681793_ab8142a537_b.jpg

3184519324_a262354f66_b.jpg

Fronts fitted with 2mm Spacer:

3183673843_05eecd62ed_b.jpg

3184513512_47ee8d3bbd_b.jpg

3183684735_d5b1e37911_b.jpg

Contact Details: PM or

Location: Sydney, NSW

Delivery & Conditions of Delivery: Pick up or I can organise freight at buyers expence!

Link to comment
https://www.sau.com.au/forums/topic/260894-ssr-professors-19/
Share on other sites

PHAT looking rims man good luck with the sale...... if i had the money and they would fit my humble little gtst i would sooooooo take them off ur hands but free bump for hot wheels

Gosh exactly what I want, although my car is only a 4stud siiiigh... :(

My knowledge of rims is pretty basic, when ordering what figure defines how deep the dish is?

Also any idea where I might buy some of these in the polished metal colour and hopefully 4-stud :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...