Jump to content
SAU Community

Recommended Posts

First of all mods please dont remove as the car is a drag car hence why i posted in drift/drag

1993 gtst skyline drag car ready to race just needs an engine package

minitubbed to fit 28x 10 rear tyre

gtr rear subframe & diff with new subframe bushes

full spool diff centre diff has been completely rebuilt

new front & rear brakes

new rear rims with near new slicks

new front rims with front runners

custom tailshaft

powerglide transmission ,6000rpm converter, billett th400 input shaft,transbrake,b&m supercooler,b&m shifter ,flexplate, makes boost in under 4 seconds with rb26/30 & gt42r

solenoid shifter

lexan windows all round

fibreglass bonnet

gtr front guards

stretched rear guards

andra 6 point roll cage with new sfi rollbar padding

sheetmetal dash with boost guage/shiftlight tachometer & warning lights

momo carbonkevlar race seat

simpson harness

diest parachute

custom fuel tank

custom puke tank

pwr radiator

gel battery

car has been completely rewired m800 loom done in techflex

comes with plenty of spares engine parts also available at extra cost

weight was 1136kg with all fluids

may separate wheels / trans for cheaper price

price is $15 000 roller minus engine/ecu/cdi

contact Jason 0424348521 or pm

post-15900-1257325096_thumb.jpg

post-15900-1257325157_thumb.jpg

post-15900-1257325237_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/294851-slo32/
Share on other sites

  • 2 weeks later...

car is also available turn key or with unassembled engine package,with motec m800,with cdi ignition at additional price

engine rb26/30

new crank nitrided balanced etc etc

block machined 010 grout filled 3/4 (still fine for street)

new argo rods & spares

new cp pistons & spares

arp rb26 head studs

crank studs

jun oil pump

ati balancer with dry sump drive & crank trigger

custom cam trigger

head machined 272 cams psi springs ferrea valves ported

custom intake with 12x 1600cc injectors 100mm throttle body motec 5bar map

hks exhaust manifold with 6x egts custom gt42r & 55mm gate

ecu motec m800

cdi msd dis4ho 3x motec twin coils top gun leads

fuel system new aeromotive belt drive pump & reg with braided lines & fittings

& many spares

Edited by jas/slo32
Link to comment
https://www.sau.com.au/forums/topic/294851-slo32/#findComment-4937240
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Finally have an update on this  Rack came in this week so I did a test fit. You do need the S chassis bushings since the rack is 5mm thinner than the R33 rack. The main issue I foresaw and ran into was one of the hardlines not lining up properly with there it's meant to on the rack. After some gentle coercing and bending very slightly, I managed to get it to fit without any kinks and keeping the hardline pretty much in all of the factory mounting positions. I did have to unbolt all of the soft mounts to move the line around so I could snake it out and bend it safely but it looks good to me for now. I'll update when the rack is fully bolted in and functioning.  
    • I hear this thread needs an update following its adventures last Wednesday!
    • What are you thinking makes a sequential shit to drive on the street? About the ONLY thing I can think of, is if you're wanting to be able to roll up to lights in third or second and pop it straight into neutral, or you want to come down two or three gears, say out of 5th and back to second, but they shift quick enough it doesn't really matter
    • I'm not a drag racing guy, but that was a good watch. Didn't Ibrahim's car have some cooch! But the big question is....WTF is with so many of them running without seatbelts!
    • Sequential Is fine to drive on the street
×
×
  • Create New...