Jump to content
SAU Community

Recommended Posts

Have the following for sale, still on the car can see running etc, made over 300kw on 18psi with current tune, most parts are brand new and have just been fitted within the last 2 months, can buy the whole lot or will separate.

located in Adelaide

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc $1850

- Tune Length stainless exhaust manifold $300

- 3.5 "Bell mouth dump front pipe $350 suit gt35 IW

- 3" Silicon Hard intake pipe & Pod Filter $100

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $400

- Z32 AFM with plug $250

- SARD 850cc side feed injectors with clips and loom all soldered in $850

- Yellow Jackets coil packs $300 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1450 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $400

- Nismo 400r Sideskirts suit r33 $300

- Cusco Coil Overs $800

- 18" x 9.5 Dtm rush wheels stretched 235's new tyres front, 255's 1/2 tread rear $1500

- Rda slotted rotors & QFM-k750 hight temp pads $450

- Nismo Fpr $120

Edited by FOOLBOOST
  • 2 weeks later...

still got injectors,, would they fir rb20det?

yes, they are side feed so no they wont, come with collars o-rings, fuel rail, loom etc bolt in

Hey mate got 200 for the coilpacks if u will take that if so pm me cheers

Tell him hes dreamin

Are the brakes front, back or both??

Brakes are complete set of front and back discs and pads used for 2months

Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Edited by nelly
Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Same as Spitfires ask Performance Wise who sells them

Edited by FOOLBOOST

Xmas specials

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc

Also comes with new 19psi actuator, and hks alloy hard out let elbow to suit. $1700

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $350

- Z32 AFM with plug $200

- SARD 850cc side feed injectors in rail with clips and loom all soldered in $750

- Yellow Jackets coil packs $280 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1300 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $350

- Nismo 400r Sideskirts suit r33 $200

- Rda slotted rotors & QFM-k750 hight temp pads $400

Edited by FOOLBOOST

will the gt35 turbo bolt upto the standard manifold?

It might actually as has the smaller comp cover, havent tried it as using that low mount manifold if it didnt could always use a 10-12mm spacer. Will put more pics up today.

hey mate pic's of side skirts please?

post-31991-1261964562_thumb.jpg post-31991-1261964572_thumb.jpg post-31991-1261964582_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi all, I’ve just finished fitting the timing belt on my RB25, following the standard procedure: rotate the crank twice, release the tensioner, then tighten it down. The belt feels tight, and you can see that clearly in the picture below I’ve heard some people say it’s actually better for the belt to be slightly loose rather than too tight, as excessive tension can lead to snapping. So that’s in the back of my mind. What I’m seeing is this:  • At idle, the belt looks fine.  • But when cranking and especially when revving (around 3–4,000 RPM), there’s a momentary flap/flex or flicker in the belt, which I’ve tried to capture in the video. So my question is — based on what you see, is this slight belt movement something you’d consider normal, or am I just being OCD? Could this amount of movement cause sync issues? Or is it just a harmless bit of flex under load?   from what I know belt flap and flex is expected when crank spins up and pull cam with it Would appreciate any thoughts or similar experiences.     IMG_7656.mov IMG_7657.mov
    • I've replaced the front brakes of my NA to 324 brembos and 350z calipers: i'm going for 225/40-18 up front and 245/35-18 in the back. I have Rays 7.5*19 ET35(225/35) in the front with 5mm spacers otherwise the calipers "lock up/ won't rotate". When i use the calculator i come up with 8*18 ET30 for 225/40...... but not sure i get problems with the calipers. Anyone riding around with 18 inch. that can confirm "that it'll fit"? In the back it's 7.5*9 ET30 (245/30) with the 5mm spacers, but there is no problem with the standard small brakes, so i want to take 8.5*18 ET25 (245/35).
    • Lol.. but then.. always come back to a JDM..
    • Glad to hear. If possible, get your tuner to check air's to make sure everything is still where it should be.
    • The problem with FB/Insta/Reddit etc comments relating to cars is simple. You get to ask a question once, and get one round of replies. For things that can actually be answered in a few lines of text, once, it's fine. After 6 hours, your original question is lost to the void. There are no follow ups, additional questions, anything. No project car is ever such a simple list of questions to ask. You need discussion.
×
×
  • Create New...